Kazimierz Czapczyk

Dr. Kazimierz Czapczyk

Gdansk University of Technology, 11/12 Narutowicza st., 80-233 Gdańsk, Poland
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 August 2021 in Materials
Verified
Journal Article
Open access
PDF file
KCKazimierz Czapczyk
Kazimierz Czapczyk
PZPaweł Zawadzki
Paweł Zawadzki
NWNatalia Wierzbicka
Natalia Wierzbicka
RTRafał Talar
Rafał Talar
The article presents the results of mechanical and tribological tests of Ni-P/Si3N4 nanocomposite coatings deposited on the AW-7075 aluminum alloy using the chemical reduction method. The influence of the chemical composition on the Vickers microhardness determined by the DSI method was examined. The nanocomposite layers were made of Si3N4 silicon nitride in a polydisperse powder with a particle size ranging from 20 to 25 nm. The influence of the content of the dispersion layer material on the adhesion to the substrate was analyzed. The abrasive wear was tested and determined in the reciprocating motion using the “ball-on-flat” method. The surface topography was examined by the contact method with the use of a profilometer. Based on the obtained test results, it was found that the Ni-P/Si3N4 layers produced in the bath with the Si3N4 nanoparticle content in the amount of 2 g/dm3 are more resistant to wear and show greater adhesion than the Ni-P/Si3N4 layers deposited in the bath with 5 g/dm3 of the dispersion phase. NiP/Si3N4 layers provide protection against abrasive wear under various loads and environmental conditions.

18 December 2020 in Materials
Verified
Journal Article
Open access
PDF file
KCKazimierz Czapczyk
Kazimierz Czapczyk
The article presents the results of tribological tests of Ni-P/Si3N4 nanocomposite and Ni-P nickel layers deposited on the AW-7075 aluminum alloy by chemical reduction method, and the AW-7075 alloy without coating. Nanocomposite layers were produced using Si3N4 siliconnitride in the form of a polydisperse powder whose particle sizes ranged from 20 to 25 nm. The influence of the content of the dispersion phase layer material on the abrasive wear, which was determined as the “ball on disc” method, was analyzed. Surface topography was examined by the contact method using a profilometer. The purpose of introducing Si3N4 particles into the Ni-P layer was to increase the wear resistance of AW-7075 aluminum alloy parts with an embedded nanocomposite coating. Based on the obtained test results, it was found that the Ni-P/Si3N4 layers are more resistant to wear than the Ni-P layers and the AW-7075 alloy layers, and are a good barrier against abrasive wear at various loads and environmental conditions.

6 September 2023 in Materials
Verified
Journal Article
Open access
PDF file
KCKazimierz Czapczyk
Kazimierz Czapczyk
PZPaweł Zawadzki
Paweł Zawadzki
NWNatalia Wierzbicka
Natalia Wierzbicka
The article presents the results of mechanical testing of Ni-P/Si3N4 nanocomposite and hybrid Ni-P/Si3N4/graphite coatings deposited on AW-7075 aluminum alloy using the chemical reduction method. In terms of mechanical testing, microhardness was measured, and surface roughness and adhesion of the coatings to the aluminum substrate were determined using the “scratch test” method. The surface morphology of the deposited layers was also analyzed using light microscopy and scanning electron microscopy. Samples made of AW-7075 aluminum alloy with electroless deposited Ni-P/Si3N4 nanocomposite, Ni-P/graphite composite and hybrid Ni-P/Si3N4/graphite coatings with different content of dispersed phases were tested, and also, for comparison purposes, the Ni-P layer that constituted the matrix of the tested materials. Reinforcing phases in the form of silicon nitride nanoparticles and graphite particles were used in the layers. The purpose of the research was a thorough characterization of the coating materials used on aluminum alloys in terms of mechanical properties. Graphite is considered in this paper as it enables the reduction of the coefficient of friction through its lubricating properties. Unfortunately, graphite is difficult to use in selected layers as the only dispersion phase, because it has much lower hardness than the Ni-P coating. For this reason, a layer with a single dispersion phase in the form of graphite will be characterized by worse mechanical properties. It is necessary to add particles or nanoparticles with hardness higher than the base Ni-P coating, e.g., Si3N4, which improve the mechanical properties of the coating. The presented analyses of the results of the conducted research complement the previous studies on selected properties of nanocomposite layers with an amorphous structure and supplement the knowledge regarding their suitability for application to aluminum machine parts.

1 May 2020 in PRZEMYSŁ CHEMICZNY
Verified
Journal Article
Closed access
KCKazimierz Czapczyk
Kazimierz Czapczyk
Nanocomposite Ni-P/Si3N4 and Ni-P layers were deposited on Al alloys by chem. redn. by using a polydisperse Si3N4 powder (grain size 20-25 nm) and studied for hardness, abrasion resistance (ball-on-disc method) and surface topogr. The addn. of Si3N4 nanoparticles resulted in improving tribol. properties of the surface layers.

28 January 2024 in PRZEMYSŁ CHEMICZNY
Verified
Journal Article
Closed access
KCKazimierz Czapczyk
Kazimierz Czapczyk
Przedstawiono wpływ obecności grafitu jako fazy dyspersyjnej na właściwości mechaniczne warstw hybrydowych Ni-P/Si3 N4 /grafit, które osadzono metodą redukcji chemicznej na stopie glinu AW-7075. Wykonano badania morfologii powierzchni warstw metodą mikroskopii świetlnej i skaningowej. Dalszą część pracy stanowiły badania mechaniczne, czyli pomiary mikrotwardości warstw oraz ich adhezji do aluminiowego podłoża, a także analizy wpływu obecności grafitu na podstawowe właściwości materiału powłokowego. Zbadano próbki ze stopu AW-7075, na których osadzono metodą bezprądową powłoki hybrydowe i porównawczo nanokompozytowe o różnym składzie chemicznym, modyfikowanym zawartością faz dyspersyjnych.