The WCCo/PCD (Diamond Dispersed Cemented Carbide—DDCC) manufactured with the use of PPS (pulse plasma sintering) are modern materials intended for cutting tools with the benefits of tungsten carbides and polycrystalline diamonds. Nevertheless, the cutting performance of DDCC materials are currently not recognized. Thus this study proposes the evaluation of technological effects of a precise groove turning process of hard-to-cut AlSi13MgCuNi alloy with DDCC tools. The conducted studies involved the measurements of machined surface topographies after grooving with different cutting parameters. In addition, the tool life and wear tests of DDCC inserts were conducted during grooving process and the obtained results were compiled with values reached during machining with cemented carbide tools. It was also proved that grooving of AlSi13MgCuNi alloy with DDCC inserts enables 5 times longer tool life and almost 3-fold increase of cutting path compared to values obtained during grooving with H3 and H10 cemented carbide inserts. Ultimately, the feed value of f = 0.15 mm/rev and cutting speed in a range of 800 m/min ≤ v_c ≤ 1000 m/min during grooving with DDCC inserts can be defined as an optimal machining parameters, enabling the maximization of tool life and improvement in surface quality.

Cortical bone machining is commonly used in craniofacial surgery. The shaping of bone surfaces requires a precise determination of the process’s complexity due to the cutting tool’s defined or undefined geometry. Therefore, research was carried out to assess the impact of the rake angle (γ), clearance angle and depth of cut (d) on the cortical bone machining process. Analysis was carried out based on the orthogonal cutting in three directions. The cutting tool shape was simplified, and the cutting forces and the chip-formation process were monitored. The highest values of the resultant cutting force and shear force were recorded for γ < 0. The specific cutting force decreases with the increase of d. Cutting in the transverse direction is characterized by the highest values of resultant cutting force and shear force. The coefficient of friction depends primarily on the d and takes a constant value or increases with the increase of γ. The tests showed that the chips are formed in the entire range of d ≥ 0.5 µm and create regular shapes for d ≥ 10 µm. The research novelty confirms that even negative cutting angles guarantee controlled cutting and can find wider application in surgical procedures.

The article presents the results of mechanical and tribological tests of Ni-P/Si₃N₄ nanocomposite coatings deposited on the AW-7075 aluminum alloy using the chemical reduction method. The influence of the chemical composition on the Vickers microhardness determined by the DSI method was examined. The nanocomposite layers were made of Si₃N₄ silicon nitride in a polydisperse powder with a particle size ranging from 20 to 25 nm. The influence of the content of the dispersion layer material on the adhesion to the substrate was analyzed. The abrasive wear was tested and determined in the reciprocating motion using the “ball-on-flat” method. The surface topography was examined by the contact method with the use of a profilometer. Based on the obtained test results, it was found that the Ni-P/Si₃N₄ layers produced in the bath with the Si₃N₄ nanoparticle content in the amount of 2 g/dm³ are more resistant to wear and show greater adhesion than the Ni-P/Si₃N₄ layers deposited in the bath with 5 g/dm³ of the dispersion phase. NiP/Si₃N₄ layers provide protection against abrasive wear under various loads and environmental conditions.

The abrasive machining of cortical tissue is used in many arthroplasties and craniofacial surgery procedures. However, this method requires further research due to the processes’ complexity and the tissue’s composite structure. Therefore, studies were carried out to assess the impact of grid geometry and the anisotropic structure of bone tissue on the cutting process and crack propagation. The analysis was performed based on an orthogonal cutting in three directions. The grain shape has been simplified, and the cutting forces, crack path and surface quality were monitored. The results indicate that a depth of cut at 100–25 µm allows the most accurate cutting control. A transverse cutting direction results in the greatest surface irregularity: Iz = 17.7%, Vvc = 3.29 mL/m² and d_f = 5.22 µm and generates the most uncontrolled cracks. Maximum fracture force values of FF > 80 N were generated for d = 175 µm. For d < 5 µm, no cracks or only slight penetration occurs. A positive γ provides greater repeatability and crack control. Negative γ generates penetrating cracks and uncontrolled material damage. The individual types of cracks have a characteristic course of changes in F_x. The clearance angle did not affect the crack propagation.

In recent years, much research has been devoted to the evaluation of physical phenomena and the technological effects of precise and micromilling processes. However, the available current literature lacks synthetic work covering the current state of the art regarding cutting force–tool displacement interactions in precise and micromilling manufacturing systems. Therefore, this literature review aims to fill this research gap and focuses on the critical literature review regarding the current state of the art within the prediction methods of cutting forces and machining system’s displacements/vibrations during precise and micromilling techniques. In the first part, a currently available cutting force, as well as the static and dynamic machining system displacement models applied in precise and micromilling conditions are presented. In the next stage, a relationship between the geometrical elements of cut and generated cutting forces and tool displacements are discussed, based on the recent literature. A subsequent part concerns the formulation of the generalized analytical models for a prediction of cutting forces and vibrations during precise and micromilling conditions. In the last stage, the conclusions and outlook are formulated based on the conducted analysis of the literature. In this context, this paper constitutes a synthetic work presenting current trends in the prediction of precise milling and micromilling mechanics.

The aim of this research was to analyze the effect of inorganic additives on the tribological properties of the high-density polyethylene (HDPE) matrix composite surface. Titanium (Ti) and hexagonal boron nitride (hBN) were added in different mass fractions. The samples were produced by pressing a pre-prepared mixture of granules. The composite samples with the following mass fractions of additives were fabricated: 5% hBN, 10% hBN, 28% Ti–2% hBN, 23% Ti–7% hBN, and 20% Ti–10% hBN. An even distribution of individual additives’ concentrations was confirmed. Observations of morphology, surface topography, hardness, and tribological measurements were conducted using reciprocating motion tests with the “pin-on-flat” and rotational tests with the “pin-on-disc” configuration. Subsequently, microscopic observations and measurements of the wear track profile were carried out. Additionally, geometry parameters of the contacting elastic body were calculated for various counter-samples. It was found that the Shore D hardness of samples containing Ti and hBN increased with the Ti content, while the coefficient of friction (COF) value decreased. The addition of hBN alone did not significantly affect the hardness, regardless of the ratio, while the COF increased with the increasing hBN content. The COF value doubled with the addition of 10% hBN (COF = 0.22), whereas the addition of 90% Ti–10% hBN resulted in a decrease in the COF value, to COF = 0.83. The highest hardness value was obtained for the sample containing 28% Ti–2% hBN (66.5), while the lowest was for the sample containing 10% hBN (63.2). The wear track analysis, including its height and width caused by deformation, was detected using a focal differentiation microscope and scanning electron microscopy. Additionally, EDS maps were generated to determine the wear characteristics of the composite.