In this study, we present a detailed comparison between a conventional supercritical drying process and an evaporative drying technique for hierarchically organized porous silica gel monoliths. These gels are based on a model system synthesized by the aqueous sol–gel processing of an ethylene-glycol-modified silane, resulting in a cellular, macroporous, strut-based network comprising anisotropic, periodically arranged mesopores formed by microporous amorphous silica. The effect of the two drying procedures on the pore properties (specific surface area, pore volume, and pore widths) and on the shrinkage of the monolith is evaluated through a comprehensive characterization by using nitrogen physisorption, electron microscopy, and small-angle X-ray scattering. It can clearly be demonstrated that for the hierarchically organized porous solids, the evaporative drying procedure can compete without the need for surface modification with the commonly applied supercritical drying in terms of the material and textural properties, such as specific surface area and pore volume. The thus obtained materials deliver a high specific surface area and exhibit overall comparable or even improved pore characteristics to monoliths prepared by supercritical drying. Additionally, the pore properties can be tailored to some extent by adjusting the drying conditions, such as temperature.
In this work, polyvinylidene fluoride (PVDF) aerogels with a tailorable phase composition were prepared by following the crystallization-induced gelation principle. A series of PVDF wet gels (5 to 12 wt.%) were prepared from either PVDF–DMF solutions or a mixture of DMF and ethanol as non-solvent. The effects of the non-solvent concentration on the crystalline composition of the PVDF aerogels were thoroughly investigated. It was found that the nucleating role of ethanol can be adjusted to produce low-density PVDF aerogels, whereas the changes in composition by the addition of small amounts of water to the solution promote the stabilization of the valuable β and γ phases. These phases of the aerogels were monitored by FTIR and Raman spectroscopies. Furthermore, the crystallization process was followed by in-time and in situ ATR–FTIR spectroscopy. The obtained aerogels displayed specific surface areas > 150 m2 g−1, with variable particle morphologies that are dependent on the non-solvent composition, as observed by using SEM and Synchrotron Radiation Computed micro-Tomography (SR-μCT).
The influence of a hierarchically structured pore system of a silica sol–gel support for application as a functional component in an acetylcholinesterase‐based enzyme array, with respect to its efficiency (response time, in particular) is investigated. Careful adjustment of synthesis parameters and a novel drying method allow to prepare monolithic silica sol–gel membranes with monomodal or hierarchical pore structures. These supports enable direct comparison regarding the influence of morphological properties on maximum acetylcholinesterase (AChE) loading by a membrane and on the apparent reaction rate of the AChE‐catalyzed degradation of acetylcholine at identical enzyme loading. It is shown for the first time that the hierarchical, meso‐macroporous material is superior over the monomodal structures (of either mesopores or macropores) regarding combined functionality and transport efficiency, as reflected in the apparent reaction rates. The advantage of the mesopores in a hierarchical system is manifested in higher maximum enzyme loading than for purely macroporous material, while the presence of macropores results in less obstructed transport that for a purely mesoporous material, which in turn reduces the response time.
In situ small-angle X-ray scattering (SAXS) was employed to identify critical parameters during thermal treatment for template removal of an ordered mesoporous carbon precursor synthesized via a direct soft-templating route. The structural parameters obtained from the SAXS data as a function of time were the lattice parameter of the 2D hexagonal structure, the diameter of the cylindrical mesostructures and a power-law exponent characterizing the interface roughness. Moreover, detailed information on contrast changes and pore lattice order was obtained from analysis of the integrated SAXS intensity of the Bragg and diffuse scattering separately. Five characteristic regions during heat treatment were identified and discussed regarding the underlying dominant processes. The influence of temperature and O2/N2 ratio on the final structure was analyzed, and parameter ranges were identified for an optimized template removal without strongly affecting the matrix. The results indicate that the final structure and controllability of the process are optimum for temperatures between 260 and 300°C with a gas flow containing 2 mol% of O2.