Alberto Lopez-Arraiza

Dr. Alberto Lopez-Arraiza

University of the Basque Country (UPV/EHU), Bilbao, Basque Country, Spain
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 July 2006 in Polymer Engineering & Science
Verified
Journal Article
Closed access
PDF file
NLN. López‐Rodríguez
N. López‐Rodríguez
Alberto Lopez-ArraizaAlberto Lopez-Arraiza
Alberto Lopez-Arraiza
Emilio MeaurioEmilio Meaurio
Emilio Meaurio
Jose-Ramon SarasuaJose-Ramon Sarasua
Jose-Ramon Sarasua

1 July 2011 in Composites Part B: Engineering
Verified
Journal Article
Closed access
IAI. Amenabar
I. Amenabar
AMA. Mendikute
A. Mendikute
Alberto Lopez-ArraizaAlberto Lopez-Arraiza
Alberto Lopez-Arraiza
MLM. Lizaranzu
M. Lizaranzu
JAJ. Aurrekoetxea
J. Aurrekoetxea

15 May 2013 in Journal of Composite Materials
Verified
Journal Article
Closed access
HDHn Dhakal
Hn Dhakal
ZZZy Zhang
Zy Zhang
NBN Bennett
N Bennett
Alberto Lopez-ArraizaAlberto Lopez-Arraiza
Alberto Lopez-Arraiza
FVFj Vallejo
Fj Vallejo
Flax and jute fibres are inexpensive and easily available bast fibres and they are extensively used as reinforcement in polymer matrix composites. However, due to their susceptibility to moisture absorption, their application is restricted to non-structural interior products. In this study, flax- and jute fibre-reinforced bioresin-based epoxy biocomposites were fabricated using hand lay-up method and their nanoindentation and flexural properties were investigated. In order to study the effects of water absorption on the nanoindentation and flexural properties, the biocomposites were subjected to water immersion tests by immersing specimens in a de-ionised water bath at 25℃ for a period of 961 h. The nanoindentation behaviour and flexural properties of water-immersed specimens were evaluated and compared alongside with dry specimens. The percentage of moisture uptake and diffusion coefficient (D) was recorded higher for jute-reinforced specimens compared with flax. The flexural properties for both types of specimens were found to decrease with increase in percentage moisture uptake. Comparison of flexural strength and flexural modulus between flax dry and flax wet biocomposites showed that wet samples lost almost 40% of strength and 69% of modulus compared with dry flax samples. The jute wet samples lost 60% of strength and 80% of modulus compared with dry samples. The nanohardness value decreased from 0.207 to 0.135 GPa for dry flax sample after immersion in water.

1 May 2014 in Polymer Testing
Verified
Journal Article
Closed access
Hom DhakalHom Dhakal
Hom Dhakal
VAV. Arumugam
V. Arumugam
AAA. Aswinraj
A. Aswinraj
CSC. Santulli
C. Santulli
ZZZhongyi Zhang
Zhongyi Zhang
Alberto Lopez-ArraizaAlberto Lopez-Arraiza
Alberto Lopez-Arraiza

15 August 2011 in Journal of Composite Materials
Verified
Journal Article
Closed access
PDF file
Alberto Lopez-ArraizaAlberto Lopez-Arraiza
Alberto Lopez-Arraiza
IAI. Amenabar
I. Amenabar
AAA. Agirregomezkorta
A. Agirregomezkorta
MSM. Sarrionandia
M. Sarrionandia
JAJ. Aurrekoetxea
J. Aurrekoetxea
The emergence of new high-performance thermoplastics to replace thermosets in fiber-reinforced polymers puts up a new challenge: their machining. In this study, carbon fiber-reinforced poly-cyclic butylene terephthalate laminates were manufactured, drilled, and inspected. Different commercial drill geometries and machining conditions were compared. Roughness, microscopy, and non-destructive tests allowed us to determine the hole quality as well as delamination. The surface tests showed better results after working at the most common cutting speed (3000 rpm) than at high speed (15,000 rpm) with a constant feed rate. This fact can be explained based on the viscoelastic properties of the matrix that becomes fragile at high cutting speeds. The Delamination factor obtained by means of Ultrasonics and X-ray Computed Tomography also confirmed that the best results are achieved with a Twist drill bit at 3000 rpm. In contrast to carbon fiber-reinforced thermosets, the detected delamination at high cutting speeds is not as remarkable as expected. These results allow us to conclude that this new composite will certainly increase production rate without delamination damage. Chip formation takes also a special role. It can be recovered to be used as reinforcement in manufacturing processes due to the recyclability of the thermoplastic matrix.

10 May 2025 in Scientific Reports
Verified
Journal Article
Open access
PDF file
Alberto Lopez-ArraizaAlberto Lopez-Arraiza
Alberto Lopez-Arraiza
LELaila Essamari
Laila Essamari
MIMaider Iturrondobeitia
Maider Iturrondobeitia
DBDavid Boullosa-Falces
David Boullosa-Falces
DJDaniel Justel
Daniel Justel
A comparative Life Cycle Assessment (LCA) was conducted between a recreational ship hull made of flax fibre-reinforced bio-based epoxy resin and a traditional ship hull made of glass fibre-reinforced polyester. Since small fibreglass boats pose an environmental problem after the end of life (EoL), the primary aim of this study was to evaluate the sustainability of the biocomposite material and identify recommendations for the future eco-design of recreational boats. The LCA study was developed according to the ISO 14,040 (ISO 14040, 2006), 14,044 (ISO 14044, 2006) methodology and the OpenLCA 2.0.4 software with the Ecoinvent v.3.9.1 database. Compared to the traditional one, the LCA of the biocomposite ship hull showed positive environmental impacts for all indicators except Terrestrial Ecotoxicity (TETP), which increased by 357% due to the use of fertilisers in flax production. Remarkably, the Global Warning Potential (GWP) decreased by 14%, the Human Toxicity Potential (HTP) diminished by 13%, and the Abiotic Depletion Potential (ADP) related to material resources was reduced by 75%. The sensitivity analysis shows that electricity consumption is the primary environmental impact driver for the FFRB ship hull. Thus, selecting renewable energy sources, such as solar or wind power, can significantly enhance sustainability. It is important to note that these impacts are influenced by the system and boundary conditions considered in the study. It was suggested that the local production of flax fibre and the use of recyclable bio-resin could improve the eco-design of the ship hull.