Optical sensors offer a painless method of monitoring blood glucose levels using various light technologies to analyze blood characteristics without penetrating the skin. The literature review part reflects the progress in optical sensor technology evaluates its potential in blood glucose monitoring by overcoming the limitations of conventional methods and recognizes the challenges and future prospects in this rapidly developing area of research. The results of empirical studies are then presented. The methodology is presented as a non-invasive method of blood glucose monitoring based on near-infrared spectroscopy. To precisely evaluate blood glucose concentrations, spectroscopy techniques involving absorption and reflection are employed at wavelengths 450, 900, 1350, and 1800 nm. After absorption and reflection of glucose molecules, light is generated. An experimental study of different samples revealed a linear relationship between the final output voltage and sugar concentration. The results demonstrate a correlation between blood glucose level and signal intensity after transmission.
In this study, we investigate a magnetically levitated electromagnetic vibration energy harvester (EMEH), in which a movable permanent magnet levitates between two fixed magnets with like poles facing the central magnet. We develop a nonlinear EMEH model and validate it experimentally, achieving strong agreement with the prototype (R2 = 0.95 for RMS EMF). Using this model, we perform a parametric analysis of excitation frequency and the spacing between the fixed magnets (d), yielding practical design criteria for geometry selection. The validated model predicts a narrow maximum; for the present configuration and parameter bounds, it occurs at d ≈ 28 mm with Pout ≈ 151.94 mW, and the corresponding energy density is ρE ≈ 9.84 mW cm−3. These results yield a practical design rule for selecting d given target metrics and dimensional constraints, providing guidance for the design of compact, low-frequency harvesters powering autonomous sensor nodes.
5 July 2022 in WSEAS TRANSACTIONS ON SYSTEMS AND CONTROL
In this article, we will consider methods for measuring the electromagnetic compatibility of telecommunication systems and study the norms of compliance with EN 55022 standards. The test equipment is RF (Microwave radio) transceiver equipment. 1.4 GHz. QAM modulation (372 MHz) was enabled in real power mode, and several experiments were also conducted. Experiments show that the parasitic radiation through the image channel at an intermediate frequency in a superheterodyne receiver is 465. At a frequency of 371.94 MHz, deviations at the quasi-peak level are set to 51 dB mv/m.
Electromagnetic vibration energy harvesters with magnetic levitation are of interest for powering autonomous low-power devices due to their high output power; however, their narrow operating region makes them sensitive to changes in the parameters of external vibration excitation. This study investigates the effects of excitation frequency and base acceleration amplitude on the harvester’s output characteristics and evaluates mean power retention under combined deviations in these parameters. Numerical simulations of steady-state regimes were performed. Within prescribed neighborhoods of operating points, the minimum mean power and local relative power variation were determined. For the configuration considered, increasing the deviation bounds from ±0.2 Hz and ±0.2 g to ±0.8 Hz and ±0.8 g reduces the highest retained fraction of the global maximum power in the investigated domain from 77.73% to 24.58%, while the local relative power variation at the corresponding operating points increases from 16.46% to 66.48%. These results highlight the risk of selecting a high-power operating point near a sharp power-drop boundary, where excitation deviations can leave the load underpowered. The proposed analysis addresses this risk by evaluating the minimum mean power across the prescribed deviation range and identifying operating regions that satisfy the load’s power requirement.
Electromagnetic vibration energy harvesters with magnetic levitation are of interest for powering autonomous low-power devices due to their high output power; however, their narrow operating region makes them sensitive to changes in the parameters of external vibration excitation. This study investigates the effects of excitation frequency and base acceleration amplitude on the harvester’s output characteristics and evaluates mean power retention under combined deviations in these parameters. Numerical simulations of steady-state regimes were performed. Within prescribed neighborhoods of operating points, the minimum mean power and local relative power variation were determined. For the configuration considered, increasing the deviation bounds from ±0.2 Hz and ±0.2 g to ±0.8 Hz and ±0.8 g reduces the highest retained fraction of the global maximum power in the investigated domain from 77.73% to 24.58%, while the local relative power variation at the corresponding operating points increases from 16.46% to 66.48%. These results highlight the risk of selecting a high-power operating point near a sharp power-drop boundary, where excitation deviations can leave the load underpowered. The proposed analysis addresses this risk by evaluating the minimum mean power across the prescribed deviation range and identifying operating regions that satisfy the load’s power requirement.
A hybrid light detection and ranging perception framework combining GroveNet-based cluster filtering with reliability-aware geometric row estimation for agricultural robot navigation is reported.