Fused filament fabrication (FFF, often called FDM) is widely used in polymer additive manufacturing; however, it suffers from mechanical anisotropy and weak bonding in the Z direction. This work examines how the infill pattern influences the tensile response of PLA parts at fixed printing conditions. Dog-bone specimens (PLA, four patterns: grid, honeycomb, rectilinear, adaptive cubic) were printed and tested in tension (n = 3 per pattern). Grid yielded the highest ultimate tensile strength, whereas honeycomb produced the largest Young’s modulus; rectilinear was intermediate and adaptive cubic was trailed in both metrics. X-ray diffraction of printed PLA showed a broad halo at 16–20° (2θ) with weak α-form reflections, consistent with largely amorphous microstructure after FFF. Together, the results indicate that, at constant material and nominal infill, pattern selection alone can shift the strength–stiffness balance, with grid favoring strength and honeycomb favoring stiffness.

Investigating failure mechanisms in cutting tools used in advanced industries like biomedical and aerospace, which operate under extreme mechanical and chemical conditions, is essential to prevent failures, optimize performance, and minimize financial losses. The diamond-turning process, operating at micrometer-length scales, forms a tightly bonded built-up edge (BUE). The tribochemical interactions between a single-crystal diamond and its deformed chip induce inter-diffusion and contact, rapidly degrading the cutting edge upon BUE fracture. These effects intensify at higher deformation speeds, contributing to the observed rapid wear of diamond tools during d-shell-rich metal machining in industrial settings. In this study, these interactions were studied with niobium (Nb) as the transition metal. Tribochemical effects were observed at low deformation speeds (quasistatic; <1 mm/s), where thermal effects were negligible under in situ conditions inside the FEI /SEM vacuum chamber room. The configuration of the interface region of diamond and transition metals was characterized and analyzed using focused ion beam (FIB) milling and subsequently characterized through transmission electron microscopy (TEM). The corresponding inter-diffusion was examined by elucidating the phase evolution, element concentration profiles, and microstructure evolution via high-resolution TEM/Images equipped with an TEM/EDS system for elemental characterization.

Wire Arc Additive Manufacturing (WAAM) has emerged as a cost-effective and high-deposition-rate technique for fabricating large-scale metallic components; however, the complex thermal history inherent to the process leads to heterogeneous microstructures that can significantly influence tribological performance. In this study, the dry sliding wear behavior of WAAM-fabricated austenitic stainless steel 308L (SS308L) was systematically investigated using a pin-on-disk configuration. The influence of applied normal load (1.5–15 N) and sliding speed (0.03–0.229 m/s) on wear volume, specific wear rate, coefficient of friction (COF), and tangential force was evaluated. Optical microstructural observations indicated features consistent with a ferritic–austenitic solidification structure, including regions resembling polygonal ferrite, Widmanstätten ferrite, and austenitic dendritic morphologies. Wear results showed that wear volume and cross-sectional area increased monotonically with increasing load, while the effect of sliding speed was comparatively less significant. The specific wear rate remained on the order of 10⁻⁴ mm³/N·m with minor variations across test conditions. The COF decreased with increasing load up to 10 N, followed by a speed-dependent response at higher loads. The findings demonstrate that load is the dominant factor governing wear behavior in WAAM SS308L, while microstructural heterogeneity may contribute to frictional stability and wear resistance. This study provides valuable insight into the structure–tribology relationship of WAAM stainless steels and supports the optimization of process parameters for wear-critical applications.

Additive manufacturing (AM) of stainless steel has been gaining industry attention in recent years due to the need to manufacture complex steel components. Many sectors stand to benefit from the design flexibility, customization, and rapid production capabilities of AM. However, the industry’s adoption of this technology remains limited due to concerns about the mechanical integrity and reliability of AM products. This experimental study examines the wear and tribological behavior of Wire Arc Additive Manufactured (WAAM) austenitic stainless steel 316L. Pin-on-disk tests were conducted using a 5 mm tungsten carbide ball under dry sliding conditions at normal loads of 1.5 and 2.5 N and sliding speeds between 0.03 and 0.229 m/s. The results showed that the coefficient of friction remained relatively stable at approximately 0.6, while wear volume generally decreased with increasing sliding speed. Lower normal loads resulted in lower wear volume, whereas the wear factor showed only limited sensitivity to the applied load. Optical microscopy revealed a ferrite–austenite microstructure with residual δ-ferrite that contributes to the observed wear behavior. These findings demonstrate the suitability of WAAM-produced 316L stainless steel for tribological applications requiring stable frictional performance.