Mauro Minervino

Dr. Mauro Minervino

Fluid Mechanics, Italian Aerospace Research Centre, Capua, Italy
orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 June 2022 in Fluids
Verified
Journal Article
Open access
PDF file
Mauro MinervinoMauro Minervino
Mauro Minervino
GAGiovanni Andreutti
Giovanni Andreutti
LRLorenzo Russo
Lorenzo Russo
RTRenato Tognaccini
Renato Tognaccini
Tip-mounted propellers can increase wing aerodynamic efficiency, and the concept is gaining appeal in the context of hybrid electrical propulsion for greener aviation, as smaller and lighter electrical motors can help with mitigating structural drawbacks of a tip engine installation. A numerical study of tip propeller effects on wing aerodynamics is herein illustrated, considering different power configurations of a Regional Aircraft wing. A drag breakdown analysis using far-field methods is presented for one of the most promising configurations, and a comparison between drag reductions obtained with a tip propeller or a standard winglet installation is also provided. Numerical flow simulations using Finite Volume Methods with actuator disk models are compared with results of a Vortex-Lattice Method, and far-field aerodynamic force calculation is performed for different mesh sizes. A wing drag reduction up to 6% (10%) is predicted under typical cruise (climb) flight conditions when wingtip-mounted propellers take over half of the total thrust usually provided by turbo-prop engines installed at inboard wing position. Drag breakdown analysis confirmed that the observed benefits mainly come from a reduction in the reversible drag component, increasing the effective wing span efficiency.

1 March 2017 in Journal of Aircraft
Verified
Journal Article
Closed access
PIPierluigi Iannelli
Pierluigi Iannelli
FMFrédéric Moens
Frédéric Moens
Mauro MinervinoMauro Minervino
Mauro Minervino
RPRita Ponza
Rita Ponza
EBErnesto Benini
Ernesto Benini
The design of high-lift systems represents a challenging task within the aerospace community, being a multidisciplinary, multi-objective, and multipoint problem. The Design, Simulation and Flight R...

31 October 2017 in International Journal of Aeroacoustics
Verified
Journal Article
Open access
LSL Sanders
L Sanders
DMD-C Mincu
D-C Mincu
PVPl Vitagliano
Pl Vitagliano
Mauro MinervinoMauro Minervino
Mauro Minervino
JKJ Kennedy
J Kennedy
GBG Bennett
G Bennett
This paper presents a numerical study of the acoustic shielding of aeroengine noise by the aircraft structure. More specifically, the engines considered are contra-rotating open rotors in pusher mode which are installed at the rear of the aircraft. Several empennage designs and engine positions are evaluated. An original method for the calculation of engine noise installation effects is presented and its application to contra-rotating open rotor propulsion is demonstrated. It is based on the weak coupling between computational fluid dynamics, an integral method based on Lighthill’s analogy for the calculation of acoustic radiation, and on a boundary element method for the calculation of the acoustic diffraction by the aircraft fuselage and empennage. The prediction of a pylon-installed (isolated) contra-rotating open rotor noise directivity is presented and compared to equivalent wind-tunnel measurements. In both cases, the simulation and experiment are performed at 1:7 scale. In addition, the installation effect of the wind-tunnel, being non-anechoic, is also assessed with the numerical approach presented. Finally, for each aircraft configuration of interest, equipped with two rear contra-rotating open rotors, the predicted noise impact on the ground is evaluated. Of these, the contra-rotating open rotor mounted above an L-tail empennage is found to be the most beneficial configuration in terms of acoustic shielding.

26 August 2019 in CEAS Aeronautical Journal
Verified
Journal Article
Closed access
PDF file
FSFulvio Sartor
Fulvio Sartor
Mauro MinervinoMauro Minervino
Mauro Minervino
JWJochen Wild
Jochen Wild
SWStefan Wallin
Stefan Wallin
HMHans Maseland
Hans Maseland
PVPetr Vrchota
Petr Vrchota

4 January 2016 in Aircraft Engineering and Aerospace Technology
Verified
Journal Article
Closed access
PVPier Luigi Vitagliano
Pier Luigi Vitagliano
Mauro MinervinoMauro Minervino
Mauro Minervino
DQDomenico Quagliarella
Domenico Quagliarella
Pietro CatalanoPietro Catalano
Pietro Catalano
Purpose – This paper aims to simulate unsteady flows with surfaces in relative motion using a multi-block structured flow solver. Design/methodology/approach – A procedure for simulating unsteady flows with surfaces in relative motion was developed, based upon a multi-block structured U-RANS flow solver1. Meshes produced in zones of the flow field with different rotation speed are connected by sliding boundaries. The procedure developed guarantees that the flux conservation properties of the original scheme are maintained across the sliding boundaries during the rotation at every time step. Findings – The solver turns out to be very efficient, allowing computation in scalar mode with single core processors as well as in parallel. It was tested by simulating the unsteady flow on a propfan configuration with two counter-rotating rotors. The comparison of results and performances with respect to an existing commercial flow solver (unstructured) is reported. Originality/value – This paper fulfils an identifie...

30 August 2013 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
DRD.G. Romano
D.G. Romano
HAHenrik Alfredsson
Henrik Alfredsson
AHA. Hanifi
A. Hanifi
Ramis ÖrlüRamis Örlü
Ramis Örlü
NTN. Tillmark
N. Tillmark
Mauro MinervinoMauro Minervino
Mauro Minervino
This document explains in its first part the design procedure adopted to design the contoured sidewalls of a swept-wing airfoil section mounted in a wind tunnel in order to satisfy the infinite swept-wing approximation. In the second part, the experimental set-up is described as well as the first results of the experimental campaign. The sidewalls are shown to play their role properly and satisfactorily provide the infinite swept-wing conditions required for subsequent investigations of the most important vortex receptivity mechanisms responsible for excitation of crossflow and Tollmien-Schlichting instability modes in the airfoil boundary layer.