Raja Mazuir Raja Ahsan Shah

Prof. Raja Mazuir Raja Ahsan Shah


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 March 2023 in Energies
Verified
Journal Article
Open access
PDF file
ARAtaur Ataur Rahman
Ataur Ataur Rahman
KAKyaw Myo Aung
Kyaw Myo Aung
SISany Ihsan
Sany Ihsan
RSRaja Mazuir Raja Ahsan Shah
Raja Mazuir Raja Ahsan Shah
Mansour Al QubeissiMansour Al Qubeissi
Mansour Al Qubeissi
MAMohannad Aljarrah
Mohannad Aljarrah
Innovations are required for electric vehicles (EVs) to be lighter and more energy efficient due to the range anxiety issue. This article introduces an intelligent control of an organic structure solar supercapacitor (OSSC) for EVs to meet electrical load demands with solar renewable energy. A carbon fibre-reinforced polymer, nano zinc oxide (ZnO), and copper oxide (CuO) fillers have been used in the development of OSSC prototypes. The organic solar cell, electrical circuits, converter, controller, circuit breaker switch, and batteries were all integrated for the modelling of OSSCs. A carbon fibre (CF)-reinforced CuO-doped polymer was utilised to improve the concentration of electrons. The negative electrodes of the CF were strengthened with nano ZnO epoxy to increase the mobility of electrons as an n-type semiconductor (energy band gap 3.2–3.4 eV) and subsequently increased to 3.5 eV by adding 6% π-carbon. The electrodes of the CF were strengthened with epoxy-filled nano-CuO as a p-type semiconductor to facilitate bore/positive charging. They improve the conductivity of the OSSC. The OSSC power storage was controlled by an adaptive neuro-fuzzy intelligent system controller to meet the load demand of EVs and auxiliary battery charging. Moreover, a fully charged OSSC (solar irradiance = 1000 W/m2) produced 561 W·h/m2 to meet the vehicle load demand with 45 A of auxiliary battery charging current. Therefore, the OSSC can save 15% in energy efficiency and contribute to emission control. The integration of an OSSC with an EV battery can minimise the weight and capacity of the battery by 7.5% and 10%, respectively.

5 September 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
Mansour Al QubeissiMansour Al Qubeissi
Mansour Al Qubeissi
FSFeras Shaban
Feras Shaban
KAKhaled Almohammadi
Khaled Almohammadi
RSRaja Mazuir Raja Ahsan Shah
Raja Mazuir Raja Ahsan Shah
This study focuses on the aerodynamic optimization of the re-entry capsule (REC) Orion Crew Exploration Vehicle (CEV) module, evaluating its performance using computational fluid dynamics (CFD). Three different models, namely Baseline, 2-Duct, and 4-Duct, are investigated under a wide range of flow speeds, from supersonic (Ma=1.6) to hypersonic (Ma=6) regimes. Thermofluids aspects, drag coefficient, surface heat flux, and the effectiveness of the modified geometry are assessed using aerodynamic and temperature-based models. The results show that the introduction of ducts in the 2-Duct and 4-Duct models leads to an average decrease in the drag coefficient of approximately 2.1% and 2.9%, respectively, compared to the baseline model, across all Mach numbers. The maximum reduction in drag coefficient is 3.55%, observed at Ma=1.4 using the 4-Duct capsule. However, it is found that the addition of extra ducts to the model increases the maximum heat transfer rate. Specifically, the heat flux is increased by up to 69% for the 4-Duct model at Ma=6, compared to the baseline model. On average, the heat flux is increased by approximately 28.6% for all conditions. The findings indicate that the introduction of ducts in the REC model improves its aerothermodynamic performance by reducing drag but also increases the heat transfer rate on the surface.

9 June 2026 in Energies
Verified
Journal Article
Open access
PDF file
Sara EL AFIASara EL AFIA
Sara EL AFIA
Francisco JuradoFrancisco Jurado
Francisco Jurado
RSRaja Mazuir Raja Ahsan Shah
Raja Mazuir Raja Ahsan Shah
Antonio Cano OrtegaAntonio Cano Ortega
Antonio Cano Ortega
The rapid growth in the electric vehicle sector has increased demand for advanced battery thermal management systems (BTMSs) with high heat-dissipation capacity and temperature uniformity. Immersion cooling using dielectric fluids has recently been recognized as a promising alternative technology to conventional indirect liquid cooling methods. This study investigates the thermal and hydrodynamic behaviour of a sixteen-lithium-ion cell battery (LIB) module immersed in low-viscosity dielectric fluids using three-dimensional computational fluid dynamics simulations. In this context, a total of twenty dielectric fluids are evaluated using the ANSYS Fluent solver, with particular emphasis on the effects of key thermophysical properties, including viscosity, density, specific heat capacity, and thermal conductivity. The simulation findings reveal that mineral oil and PAO4 yield the lowest maximum LIB cell temperatures, with a reduction of approximately 4 K compared to the least effective dielectric fluids, such as undecane and cumene. Moreover, in terms of temperature uniformity, mineral oil, Novec 7000, and PAO4 exhibit the most homogeneous temperature distributions among the twenty dielectric fluids. In addition, they show an improvement in the temperature uniformity index of approximately 32.4% compared with the least effective dielectric fluid, cumene. On the other hand, mineral oil and PAO4 generate significantly higher pressure drops because of their relatively high viscosities, which increases hydraulic resistance and pumping power requirements. These findings demonstrate that excellent thermal performance does not necessarily correspond to optimal overall thermo-hydraulic behaviour. Overall, the results confirm that immersion-BTMS performance is governed by a complex interaction between dielectric fluid thermophysical properties and flow behaviour, highlighting the importance of coupled thermo-hydraulic optimization in the selection of dielectric fluids for next-generation immersion-cooled battery systems.