Mehmet Yildirim

Mr. Mehmet Yildirim

Cracow University of Technology, Department of Energy
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 June 2022 in Energy
Verified
Journal Article
Open access
Mehmet YildirimMehmet Yildirim
Mehmet Yildirim
ACArtur Cebula
Artur Cebula
MSMaciej Sułowicz
Maciej Sułowicz

7 December 2023 in Energy
Verified
Journal Article
Closed access
Mehmet YildirimMehmet Yildirim
Mehmet Yildirim
ACArtur Cebula
Artur Cebula

20 December 2020 in Energies
Verified
Journal Article
Open access
PDF file
Mehmet YildirimMehmet Yildirim
Mehmet Yildirim
MNMarzena Nowak-Ocłoń
Marzena Nowak-Ocłoń
Solar photovoltaic (PV) energy is one of the most viable renewable energy sources, considered less polluting than fossil energy. However, the average power conversion efficiency of PV systems is between 15% and 20%, and they must operate with high efficiency. Photovoltaic cells have non-linear voltage–current characteristics that are dependent on environmental factors such as solar irradiation and temperature, and have low efficiency. Therefore, it becomes crucial to harvest the maximum power from PV panels. This paper aims to study and analyze the most common and well-known maximum power point tracking (MPPT) algorithms, perturb and observe (P&O) and incremental conductance (IncCond). These algorithms were found to be easy to implement, low-cost techniques suitable for large- and medium-sized photovoltaic applications. The algorithms were tested and compared dynamically using MATLAB/Simulink software. In order to overcome the low performance of the P&O and IncCond methods under time-varying and fast-changing solar irradiation, several modifications are proposed. Results show an improvement in the tracking and overall system efficiencies and a shortened response time compared with original techniques. In addition, the proposed algorithms minimize the oscillations around the maximum power point (MPP), and the power converges faster.


10 November 2021
Verified
Conference Paper
Open access
PDF file
Mehmet YildirimMehmet Yildirim
Mehmet Yildirim
ACArtur Cebula
Artur Cebula
This paper presents a review of recent photovoltaic cooling technologies and techniques used to reduce the negative impact of increased temperature to enhance the production of electricity by photovoltaic (PV) modules. Various cooling methods are reviewed; namely, Thermoelectric cooling, PV cooling with phase change materials (PCM) and nanofluids, PV systems cooled by forced water circulation, water immersion cooling technique, PV systems cooled by heat sinks, and solar PV systems cooled by water spraying. Several research papers are reviewed, and their focus is explained to provide an understanding of each cooling method to decrease the surface temperature of PV modules. In the conclusion section, the advantages and disadvantages of the above-mentioned cooling methods are expressed. This work can be used by engineers working on the design and theory of cooled photovoltaic systems.

2 September 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MZMichal Zielina
Michal Zielina
BKBartosz Kopiczak
Bartosz Kopiczak
ACArtur Tadeusz Cebula
Artur Tadeusz Cebula
Mehmet YildirimMehmet Yildirim
Mehmet Yildirim
This paper presents a combined CFD and experimental investigation of water flow through a Shootfire-1000 water-foam fire monitor. The study aimed to assess pressure losses, flow characteristics, hydraulic stability, and cavitation risk, and to evaluate the influence of selected geometric and operating parameters on hydraulic performance. A numerical model based on the actual geometry of the device was developed and experimentally validated using pressure loss measurements obtained under representative operating conditions. The influence of flow rate, monitor elevation angle, water temperature, nozzle cone position, and cone plate fillet radius was analyzed. The results showed that the dominant pressure losses occur within the monitor head, particularly in the annular constriction formed by the nozzle cone and the housing. Water temperature and monitor elevation angle had only a minor effect on the overall hydraulic performance, whereas relatively small modifications of the nozzle cone geometry significantly affected pressure losses. The analyses further demonstrated that local geometric features play a key role in determining velocity distribution and hydraulic stability. No pressure values below the water vapour pressure were observed within the investigated operating range, indicating a negligible risk of cavitation. The results confirm that optimization of the monitor head geometry can effectively reduce hydraulic losses and improve the hydraulic performance of water-foam fire monitors.