AlxIn1−xN ternary semiconductors have attracted much interest for application in photovoltaic devices. Here, we compare the material quality of AlxIn1−xN layers deposited on Si with different crystallographic orientations, (100) and (111), via radio-frequency (RF) sputtering. To modulate their Al content, the Al RF power was varied from 0 to 225 W, whereas the In RF power and deposition temperature were fixed at 30 W and 300 °C, respectively. X-ray diffraction measurements reveal a c-axis-oriented wurtzite structure with no phase separation regardless of the Al content (x = 0–0.50), which increases with the Al power supply. The surface morphology of the AlxIn1−xN layers improves with increasing Al content (the root-mean-square roughness decreases from ≈12 to 2.5 nm), and it is similar for samples grown on both Si substrates. The amorphous layer (~2.5 nm thick) found at the interface with the substrates explains the weak influence of their orientation on the properties of the AlxIn1−xN films. Simultaneously grown AlxIn1−xN-on-sapphire samples point to a residual n-type carrier concentration in the 1020–1021 cm−3 range. The optical band gap energy of these layers evolves from 1.75 to 2.56 eV with the increase in the Al. PL measurements of AlxIn1−xN show a blue shift in the peak emission when adding the Al, as expected. We also observe an increase in the FWHM of the main peak and a decrease in the integrated emission with the Al content in room-temperature PL measurements. In general, the material quality of the AlxIn1-xN films on Si is similar for both crystallographic orientations.
16 March 2024 in Materials Science in Semiconductor Processing
Sputtering is a deposition technique used to fabricate low‐cost silicon films on crystalline and amorphous substrates. Herein, the deposition of amorphous silicon films by DC sputtering on both sapphire and GaN/sapphire substrates is reported. Films are deposited using argon plasma with a pressure of 0.47 Pa at 30–60 W of DC power and different deposition temperatures from RT to 550 °C. The effect of different deposition conditions is investigated on structural quality, layer morphology, and optical properties of the layers. X‐ray diffraction measurements do not show any peak associated to crystalline silicon, while energy‐dispersive X‐ray demonstrates the presence of silicon in the layers. Silicon films deposited on sapphire show a compact morphology but the formation of silicon columns on GaN. On both substrates, the growth rate increases a factor of 3 with the applied DC power (50–150 nm h−1). Finally, the optical bandgap energy extracted from transmission measurements decreases from 2.40 to 2.10 eV with the DC power, due to the reduction of impurity incorporation. This work offers a low‐cost alternative for the deposition of amorphous compact silicon films and silicon nanocolumns at low temperature, for application in sensing, photonic, electronic, and photovoltaic devices.
Aluminum nitride (AlN) is a material of wide interest in the optoelectronics and high-power electronics industry. The deposition of AlN thin films at elevated temperatures is a well-established process, but its implementation on flexible substrates with conductive oxides, such as ITO-glass or ITO-PET, poses challenges due to the thermal degradation of these materials. In this work, the deposition and characterization of AlN thin films by reactive sputtering at a low temperature (RT and 100 °C) on ITO-glass and ITO-PET substrates are presented. The structural, optical, and electrical properties of the samples have been analysed as a function of the sputtering power and the deposition temperature. XRD analysis revealed the absence of peaks of crystalline AlN, indicative of the formation of an amorphous phase. EDX measurements performed on the ITO-glass substrate with a radiofrequency power applied to the Al target of 175 W confirmed the presence of Al and N, corroborating the deposition of AlN. SEM analyses showed the formation of homogeneous and compact layers, and transmission optical measurements revealed a bandgap of around 5.82 eV, depending on the deposition conditions. Electrical resistivity measurements indicated an insulating character. Overall, these findings confirm the potential of amorphous AlN for applications in flexible optoelectronic devices.
Here, we report the first experimental demonstration of InN nanowire solar cells deposited by RF sputtering with a bandgap energy of 1.78 eV. By adding an amorphous Si (a-Si) buffer to the n-InN/p-Si structure, we have improved the photovoltaic performance of the resulting devices while maintaining their material quality. We have firstly optimized the deposition of Si on Si(100) by DC sputtering, obtaining an amorphous material with bandgap energy of 1.39 eV. Then we have studied the influence of the thickness of the a-Si buffer layer (0-25 nm) on the structural, morphological, electrical, and optical properties of InN nanowires on Si (100) substrates. With the use of a 15-nm buffer, n-InN/a-Si/p-Si nanowire heterojunction solar cells exhibit a promising short-circuit current density of 17 mA/cm2, open circuit voltage of 0.37 V and fill factor of 35.5%, pointing to a power-conversion efficiency of 2.3% under 1-sun (AM 1.5G) illumination. These work demonstrated that the combination of in-situ sputtered a-Si, which could serve as potential passivation layer, and the light trapping enhancement by the nanostructured active layer leads to an improvement of the photovoltaic efficiency of sputtered III-nitride devices.