Fernando Naranjo

Dr. Fernando Naranjo

Electronics Department, EPS (GRIFO), University of Alcalá, Alcalá de Henares, Spain

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 May 2020 in Materials
Verified
Journal Article
Open access
PDF file
SVSirona Valdueza-Felip
Sirona Valdueza-Felip
RBRodrigo Blasco
Rodrigo Blasco
JOJavier Olea
Javier Olea
ADAlba Díaz-Lobo
Alba Díaz-Lobo
ACAlejandro Francisco Braña de Cal
Alejandro Francisco Braña de Cal
Fernando NaranjoFernando Naranjo
Fernando Naranjo
We investigate the photovoltaic performance of solar cells based on n-AlxIn1−xN (x = 0–0.56) on p-Si (100) hetero-junctions deposited by radio frequency sputtering. The AlxIn1−xN layers own an optical bandgap absorption edge tuneable from 1.73 eV to 2.56 eV within the Al content range. This increase of Al content results in more resistive layers (≈10−4–1 Ω·cm) while the residual carrier concentration drops from ~1021 to ~1019 cm−3. As a result, the top n-contact resistance varies from ≈10−1 to 1 MΩ for InN to Al0.56In0.44N-based devices, respectively. Best results are obtained for devices with 28% Al that exhibit a broad external quantum efficiency covering the full solar spectrum with a maximum of 80% at 750 nm, an open-circuit voltage of 0.39 V, a short-circuit current density of 17.1 mA/cm2 and a conversion efficiency of 2.12% under air mass 1.5 global (AM1.5G) illumination (1 sun), rendering them promising for novel low-cost III-nitride on Si photovoltaic devices. For Al contents above 28%, the electrical performance of the structures lessens due to the high top-contact resistivity.

21 October 2022 in Materials
Verified
Journal Article
Open access
PDF file
MSMichael Sun
Michael Sun
RBRodrigo Blasco
Rodrigo Blasco
Julian NwodoJulian Nwodo
Julian Nwodo
María De La MataMaría De La Mata
María De La Mata
Sergio I MolinaSergio I Molina
Sergio I Molina
Fernando NaranjoFernando Naranjo
Fernando Naranjo
AlxIn1−xN ternary semiconductors have attracted much interest for application in photovoltaic devices. Here, we compare the material quality of AlxIn1−xN layers deposited on Si with different crystallographic orientations, (100) and (111), via radio-frequency (RF) sputtering. To modulate their Al content, the Al RF power was varied from 0 to 225 W, whereas the In RF power and deposition temperature were fixed at 30 W and 300 °C, respectively. X-ray diffraction measurements reveal a c-axis-oriented wurtzite structure with no phase separation regardless of the Al content (x = 0–0.50), which increases with the Al power supply. The surface morphology of the AlxIn1−xN layers improves with increasing Al content (the root-mean-square roughness decreases from ≈12 to 2.5 nm), and it is similar for samples grown on both Si substrates. The amorphous layer (~2.5 nm thick) found at the interface with the substrates explains the weak influence of their orientation on the properties of the AlxIn1−xN films. Simultaneously grown AlxIn1−xN-on-sapphire samples point to a residual n-type carrier concentration in the 1020–1021 cm−3 range. The optical band gap energy of these layers evolves from 1.75 to 2.56 eV with the increase in the Al. PL measurements of AlxIn1−xN show a blue shift in the peak emission when adding the Al, as expected. We also observe an increase in the FWHM of the main peak and a decrease in the integrated emission with the Al content in room-temperature PL measurements. In general, the material quality of the AlxIn1-xN films on Si is similar for both crystallographic orientations.

4 November 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Laura MonroyLaura Monroy
Laura Monroy
MJMarco Jiménez-Rodríguez
Marco Jiménez-Rodríguez
EMEva Monroy
Eva Monroy
MHMiguel González Herráez
Miguel González Herráez
Fernando NaranjoFernando Naranjo
Fernando Naranjo
New fabrication methods are strongly demanded for the development of thin-film saturable absorbers with improved optical properties (absorption band, modulation depth, nonlinear optical response). In this sense, we investigate the performance of indium nitride (InN) epitaxial layers with low residual carrier concentration (<1018 cm−3), which results in improved performance at telecom wavelengths (1560 nm). These materials have demonstrated a huge modulation depth of 23% and a saturation fluence of 830 µJ/cm2, and a large saturable absorption around −3 × 104 cm/GW has been observed, attaining an enhanced, nonlinear change in transmittance. We have studied the use of such InN layers as semiconductor saturable absorber mirrors (SESAMs) for an erbium (Er)-doped fiber laser to perform mode-locking generation at 1560 nm. We demonstrate highly stable, ultrashort (134 fs) pulses with an energy of up to 5.6 nJ.

29 August 2025 in Micromachines
Verified
Journal Article
Open access
PDF file
MCMiriam Cadenas
Miriam Cadenas
MSMichael Sun
Michael Sun
Susana FernándezSusana Fernández
Susana Fernández
SVSirona Valdueza-Felip
Sirona Valdueza-Felip
Ana Maria Diez-PascualAna Maria Diez-Pascual
Ana Maria Diez-Pascual
Fernando NaranjoFernando Naranjo
Fernando Naranjo
Aluminum nitride (AlN) is a material of wide interest in the optoelectronics and high-power electronics industry. The deposition of AlN thin films at elevated temperatures is a well-established process, but its implementation on flexible substrates with conductive oxides, such as ITO-glass or ITO-PET, poses challenges due to the thermal degradation of these materials. In this work, the deposition and characterization of AlN thin films by reactive sputtering at a low temperature (RT and 100 °C) on ITO-glass and ITO-PET substrates are presented. The structural, optical, and electrical properties of the samples have been analysed as a function of the sputtering power and the deposition temperature. XRD analysis revealed the absence of peaks of crystalline AlN, indicative of the formation of an amorphous phase. EDX measurements performed on the ITO-glass substrate with a radiofrequency power applied to the Al target of 175 W confirmed the presence of Al and N, corroborating the deposition of AlN. SEM analyses showed the formation of homogeneous and compact layers, and transmission optical measurements revealed a bandgap of around 5.82 eV, depending on the deposition conditions. Electrical resistivity measurements indicated an insulating character. Overall, these findings confirm the potential of amorphous AlN for applications in flexible optoelectronic devices.

27 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
ANArántzazu Núñez-Cascajero
Arántzazu Núñez-Cascajero
Fernando NaranjoFernando Naranjo
Fernando Naranjo
María De La MataMaría De La Mata
María De La Mata
Sergio I MolinaSergio I Molina
Sergio I Molina
Compact Al0.37In0.63N layers were grown by radiofrequency sputtering on bare and 15 nm-thick AlN-buffered Si (111) substrates. The crystalline quality of the AlInN layers was studied by high-resolution X-ray diffraction measurements and transmission electron microscopy. Both techniques show an improvement of the structural properties when the AlInN layer is grown on a 15 nm-thick AlN buffer. The layer grown on bare silicon exhibits a thin amorphous interfacial layer between the substrate and the AlInN, which is not present in the layer grown on the AlN buffer layer. A reduction of the density of defects is also observed in the layer grown on the AlN buffer.