Milan Švanda

Dr. Milan Švanda

Czech Technical University in Prague, Prague, Praha, Hlavní Město, Czech Republic
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2016 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
MPMilan Polivka
Milan Polivka
JHJaroslav Havlicek
Jaroslav Havlicek
MŠMilan Švanda
Milan Švanda
JMJan Machac
Jan Machac
This letter presents significant improvement in robustness and recognizability of radar cross section (RCS) response of the two topologically rearranged 20-bit U-shaped strip-based tags for spectral signature-based chipless RFID systems. The space rearrangement of individual tag scatterers in the array reduces the interelement mutual coupling and, thus, significantly enhances the frequency and amplitude robustness of their RCS. In comparison to the original arrangement of scatterers, the measurement of tags designed for 2-4-GHz frequency band showed a significantly improved homogeneity of the RCS curve, which results in a more reliable recognition of coded information.

12 February 2015 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
MŠMilan Švanda
Milan Švanda
MPMilan Polivka
Milan Polivka
This paper introduces a novel impedance matching technique for extremely low-profile on-body UHF RFID tag antennas based on coupled shorted-patch antennas. The approach employs a novel arrangement of comb-notches perpendicular to the central radiation slot that excites the close higher order mode that affects the field distribution of the fundamental mode and sets the input impedance to the required complex values of UHF RFID chips over the range of 5-50 Ω for the real part and 100-200 Ω for the imaginary part, or directly to 50 Ω impedance. A set of parametric studies shows the flexibility of the proposed technique for achieving complex input impedances. To verify the proposed technique, we have developed and measured two antenna samples of relative size 0.3 × 0.17 × 0.0022λ 0 . A first antenna is matched to 50 Ω, and is intended to be used as an on-body antenna sensor for mapping the received signal strength in applications of the European UHF RFID band. The second antenna operates as an RFID tag antenna with input impedance in Z in = 22 + j195 Ω, and reaches a read range of 7.3 m.

14 August 2019 in IEEE Access
Verified
Journal Article
Open access
MŠMilan Švanda
Milan Švanda
MPMilan Polivka
Milan Polivka
JHJaroslav Havlicek
Jaroslav Havlicek
JMJan Machac
Jan Machac
DWDouglas H. Werner
Douglas H. Werner
In this paper, we first carry out an in-depth review of the performance parameters of frequency-domain chipless RFID transponders in terms of their spatial density, spectral capacity, and comprehensive encoding capacity (bit/λ2/GHz) comprising both spatial and spectral performance, and platform tolerance. Secondly, we theoretically and numerically investigate the recently introduced and promising concept of the platform-tolerant chipless RFID transponder based on a detuned dipole array-plate that provides high encoding capacity. We propose, fabricate and measure a 20-bit transponder consisting of an array of 20 detuned dipoles closely coupled to a 60 × 60 mm2 metallic plate. The radar cross section at the level of -15 dBsm exhibits reliably recognizable minima corresponding to individual dipole resonances. When compared to other published frequency-domain chipless RFID transponders, the encoding capacity reaches 47.4 bit/λ2/GHz, which constitutes one of the highest values, while achieving a concurrently high level of radar cross section (RCS) reflection response and platform tolerance performance. The measurements confirm very good performance parameters in the cases when the transponder is attached to various packaging materials, such as cardboard, plastic, wood, metal or a human body phantom. The essential benefits of the presented solution include a very good frequency and amplitude stability in the RCS response, which enables a reliable reading of encoded information (if zero bits are coded). The double layer metallization represents an inherent property of the proposed solution, which is a necessary trade-off for high encoding capacity and contemporary platform tolerance.

14 April 2009 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
MPMilan Polivka
Milan Polivka
MŠMilan Švanda
Milan Švanda
PHPremysl Hudec
Premysl Hudec
SZStanislav Zvanovec
Stanislav Zvanovec
The performance of an ultra-high-frequency RF identification (ID) system operating at 869 MHz, intended for the ID of persons in both indoor and open areas, has been validated using the propagation models, as well as the series of practical measurements. A two-ray propagation model and the 3-D ray-tracing model were used for calculations of all important system parameters in open and indoor areas, respectively. For the application mentioned above, a novel (electrically small and, at the same time, low-profile) wearable TAG antenna was designed. It was used in order to carry out the necessary tests as well. The antenna in question is based on an artificial-like surface. The latter provides an important screening effect and avoids detuning. Another virtue of the surface used is represented by the fact that it ensures the minimum loss of the antenna efficiency (resulting from the presence of a nearby human body). The simulations and measurements show that the optimized system can guarantee a reliable ID at distances up to 9 m in open areas and up to 16 m in corridors.

10 October 2017 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
JHJaroslav Havlicek
Jaroslav Havlicek
MŠMilan Švanda
Milan Švanda
MPMilan Polivka
Milan Polivka
JMJan Machac
Jan Machac
Jan KracekJan Kracek
Jan Kracek
This letter presents the novel 20 bit chipless radiofrequency identification transponder (tag) based on spiral capacitively loaded dipole scatterers of electrical size ka = 0.47, radar cross-section (RCS) σ = -29.3 dBsm, and bandwidth BW3dB = 20.9 MHz. It outperforms U-folded dipole scatterer (ka = 0.79, σ = -34.3 dBsm, BW3dB = 18.1 MHz) in the first two parameters in exchange for a slight increase in bandwidth. The total tag size (17 × 68 mm2) is roughly half the size of a credit card. The frequency and amplitude stability of its RCS response, when the zero bit information is coded via removal of individual scatterers, is improved by reordering scatterers in the array. The simulated results were verified by the monostatic measurement of tag RCS.

15 September 2021 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
MPMilan Polívka
Milan Polívka
VHVaclav Hubata-Vacek
Vaclav Hubata-Vacek
MŠMilan Švanda
Milan Švanda
The article presents a novel design of a compact wearable harmonic transponder with double-plane symmetry, composed of a dual-band patch-type antenna loaded by an HSMS-2820 Schottky diode, operated as a proof of concept at ISM UHF 869 and 1734 MHz frequencies. The antenna is analyzed and optimized for a minimum ground plate size by means of the CST Microwave Studio electromagnetic simulator, and its reflection coefficient is incorporated into the equivalent circuit model for a combined harmonic balance (HB) and full-wave analysis using the AWR Microwave Office commercial simulator. The transponder performance, including the complex input impedance matching and conversion loss (CL) between the fundamental and second harmonic frequencies on the diode, was evaluated both in free space and when attached to a human muscle phantom. The total harmonic transponder CL, including diode CL, antenna transponder gains, and impedance mismatching, is 6.2 dB for an excitation power of −25 dBm at the antenna–diode interface. The measured reading distances are 9.0 and 8.8 m for equivalent isotropically radiated power (EIRP) $=20$ dBm when the transponder is placed in free space and on the human body, respectively. As a means of machine-to-person communication, the transponder is suitable for the Internet of Things (IoT) concept, e.g., for the identification of pedestrians in traffic, i.e., in a complex environment with unwanted radiation clutter and multipath fading.