Mohammad - Azeem

Mr. Mohammad - Azeem

Universiti Teknologi Petronas, Ipoh, Perak, Malaysia
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 March 2021 in Sustainability
Verified
Journal Article
Open access
PDF file
SIVABALAN KANIAPANSIVABALAN KANIAPAN
SIVABALAN KANIAPAN
SHSuhaimi Hassan
Suhaimi Hassan
HYHamdan H. Ya
Hamdan H. Ya
Kartikeyan Patma NesanKartikeyan Patma Nesan
Kartikeyan Patma Nesan
MAMohammad - Azeem
Mohammad - Azeem
The importance of energy demands that have increased exponentially over the past century has led to the sourcing of other ideal power solutions as the potential replacement alternative to the conventional fossil fuel. However, the utilisation of fossil fuel has created severe environmental issues. The identification of other renewable sources is beneficial to replace the energy utilisation globally. Biomass is a highly favourable sustainable alternative to renewable resources that can produce cleaner, cheaper, and readily available energy sources in the future. The palm oil industry is essentially ideal for the availability of abundant biomass resources, where the multifaceted residues are vital for energy production through the conversion of biomass waste into value-added products simultaneously. This article discusses the utilisation of palm oil and its residues in the energy and transportation sector. Assessment and evaluation on the feasibility of palm oil and its residues were made on the current valorisation methods such as thermochemical and biochemical techniques. Their potential as transportation fuels were concurrently reviewed. This is followed by a discussion on future challenges of palm oil industries that will take place globally, including the prospects from government and nongovernment organisations for the development of palm oil as a sustainable alternative replacement to fossil fuel. Hence, this review aims to provide further insight into the possibilities of palm oil and its residues towards sustainable development with reduced environmental-related issues.

18 January 2024 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
Quanjin MaQuanjin Ma
Quanjin Ma
MRM.R.M. Rejab
M.R.M. Rejab
MAMohammad - Azeem
Mohammad - Azeem
SHShukur Abu Hassan
Shukur Abu Hassan
BYBinghua Yang
Binghua Yang
AKA. Praveen Kumar
A. Praveen Kumar

13 December 2023 in Results in Engineering
Verified
Journal Article
Open access
MAMohammad - Azeem
Mohammad - Azeem
HYHamdan H. Ya
Hamdan H. Ya
MAMohammad Azad Alam
Mohammad Azad Alam
MKMukesh Kumar
Mukesh Kumar
ZSZubair Sajid
Zubair Sajid
SKSanan H. Khan
Sanan H. Khan

29 December 2023 in Results in Engineering
Verified
Journal Article
Open access
MAMohammad - Azeem
Mohammad - Azeem
HYHamdan H. Ya
Hamdan H. Ya
MAMohammad Azad Alam
Mohammad Azad Alam
MMMasdi Muhammad
Masdi Muhammad
SSSalit M Sapuan
Salit M Sapuan
SKSanan H. Khan
Sanan H. Khan

16 October 2020 in Materials
Verified
Journal Article
Open access
PDF file
RKRehan Khan
Rehan Khan
HYHamdan H. Ya
Hamdan H. Ya
WPWilliam Pao
William Pao
MMMohd Amin Abd Majid
Mohd Amin Abd Majid
TATauseef Ahmed
Tauseef Ahmed
HIHassan Iftikhar
Hassan Iftikhar
Erosion-corrosion of elbow configurations has recently been a momentous concern in hydrocarbon processing and transportation industries. The carbon steel 90° elbows are susceptible to the erosion-corrosion during the multiphase flow, peculiarly for erosive slug flows. This paper studies the erosion-corrosion performance of 90° elbows at slug flow conditions for impact with 2, 5, and 10 wt.% sand fines concentrations on AISI 1018 carbon steel exploiting quantitative and qualitative analyses. The worn surface analyses were effectuated by using laser confocal and scanning electron microscopy. The experiment was conducted under air and water slug flow containing sand fines of 50 µm average size circulated in the closed flow loop. The results manifest that with the increase of concentration level, the erosion-corrosion magnitude increases remarkably. Sand fines instigate the development of perforation sites in the form of circular, elongated, and coalescence pits at the elbow downstream and the corrosion attack is much more obvious with the increase of sand fines concentration. Another congruent finding is that cutting and pitting corrosion as the primitive causes of material degradation, the 10 wt.% sand fines concentration in carrier phase increases the erosion-corrosion rate of carbon steel up to 93% relative to the 2 wt.% sand fines concentration in slug flow.

23 May 2022 in Materials
Verified
Journal Article
Open access
PDF file
MKMuhammad Rehan Khan
Muhammad Rehan Khan
HYHamdan H. Ya
Hamdan H. Ya
Imran ShahImran Shah
Imran Shah
UKUsama Khan
Usama Khan
BABilal Anjum Ahmed
Bilal Anjum Ahmed
TATauseef Ahmed
Tauseef Ahmed
Erosive wear due to the fact of sand severely affects hydrocarbon production industries and, consequently, various sectors of the mineral processing industry. In this study, the effect of the elbow geometrical configuration on the erosive wear of carbon steel for silt–water–air flow conditions were investigated using material loss analysis, surface roughness analysis, and microscopic imaging technique. Experiments were performed under the plug flow conditions in a closed flow loop at standard atmospheric pressure. Water and air plug flow and the disperse phase was silt (silica sand) with a 2.5 wt % concentration, and a silt grain size of 70 µm was used for performing the tests. The experimental analysis showed that silt impact increases material disintegration up to 1.8 times with a change in the elbow configuration from 60° to 90° in plug flow conditions. The primary erosive wear mechanisms of the internal elbow surface were sliding, cutting, and pit propagation. The maximum silt particle impaction was located at the outer curvature in the 50° position in 60° elbows and the 80° position in 90° elbows in plug flow. The erosion rate decreased from 10.23 to 5.67 mm/year with a change in the elbow angle from 90° to 60°. Moreover, the microhardness on the Vickers scale increased from 168 to 199 in the 90° elbow and from 168 to 184 in the 60° elbow.