A discretized positioning circuit (DPC) based on a resistive network has been developed to reduce the size of a gamma-ray detection system using multi-anode photomultiplier tubes (MA-PMT) in an array, because it can drastically decrease the number of output channels. The output signal from the gamma-ray detection system is a current pulse generated in each tube that contains information about the gamma-ray energy and detecting position in the array. The output current pulse is distributed to four outputs according to the resistance ratio of the resistive network in the DPC, and the detected position is estimated using the height values of the four distributed current pulses. However, owing to parasitic capacitors of MA-PMT connected in parallel to resistors in the resistive network, the four output pulses are affected by the RC time constants. In particular, when the duration of the input signal is not long enough, the height values of the distributed pulses are reduced, and thereby the position error increases significantly. In this paper, we present a new distortion correction method that considers the pulse duration and the RC time constant. In order to correct the position error, we employed homography, which is a coordinate transformation method. The ideal grid was mapped to a new grid for the distorted position. Using this method, error correction was completely achieved, even for short current pulses.
Replica molding-based triboelectrification has emerged as a new and facile technique to generate nanopatterned tribocharge on elastomer surfaces. The “mechano-triboelectric charging model” has been developed to explain the mechanism of the charge formation and patterning process. However, this model has not been validated to cover the full variety of nanotexture shapes. Moreover, the experimental estimation of the tribocharge’s surface density is still challenging due to the thick and insulating nature of the elastomeric substrate. In this work, we perform experiments in combination with numerical analysis to complete the mechano-triboelectrification charging model. By utilizing Kelvin probe force microscopy (KPFM) and finite element analysis, we reveal that the mechano-triboelectric charging model works for replica molding of both recessed and protruding nanotextures. In addition, by combining KPFM with numerical electrostatic modeling, we improve the accuracy of the surface charge density estimation and cross-calibrate the result against that of electrostatic force microscopy. Overall, the regions which underwent strong interfacial friction during the replica molding exhibited high surface potential and charge density, while those suffering from weak interfacial friction exhibited low values on both. These multi-physical approaches provide useful and important tools for comprehensive analysis of triboelectrification and generation of nanopatterned tribocharge. The results will widen our fundamental understanding of nanoscale triboelectricity and advance the nanopatterned charge generation process for future applications.
Soft material-based pneumatic microtube actuators are attracting intense interest, since their bending motion is potentially useful for the safe manipulation of delicate biological objects. To increase their utility in biomedicine, researchers have begun to apply shape-engineering to the microtubes to diversify their bending patterns. However, design and analysis of such microtube actuators are challenging in general, due to their continuum natures and small dimensions. In this paper, we establish two methods for rapid design, analysis, and optimization of such complex, shape-engineered microtube actuators that are based on the line-segment model and the multi-segment Euler–Bernoulli’s beam model, respectively, and are less computation-intensive than the more conventional method based on finite element analysis. To validate the models, we first realized multi-segment microtube actuators physically, then compared their experimentally observed motions against those obtained from the models. We obtained good agreements between the three sets of results with their maximum bending-angle errors falling within ±11%. In terms of computational efficiency, our models decreased the simulation time significantly, down to a few seconds, in contrast with the finite element analysis that sometimes can take hours. The models reported in this paper exhibit great potential for rapid and facile design and optimization of shape-engineered soft actuators.
Two-dimensional (2-D) metal nanodot arrays (NDAs) have been attracting significant attention for use in biological and chemical sensing applications. The unique optical properties of the metal NDAs originate from their localized surface plasmon resonance (LSPR). Nanofabrication methods that use nanoporous alumina masks (NAMs) have been widely used to produce metal NDAs. We report a fabrication technique for a 2-D Ag NDA and its utilization as a platform for LSPR-based sensing applications. A well-ordered Ag NDA of diameter, arranged in a periodic pattern of 105 nm, was fabricated on an indium tin oxide (ITO) glass substrate using an NAM as an evaporation mask. The LSPR of the Ag NDA on the ITO glass was investigated using ultraviolet–visible spectroscopy. The LSPR wavelength shifts caused by the variations in the quantity of methylene blue adsorbed on the Ag NDA were examined. The results of this study suggest that the Ag NDA prepared using NAM can be used as a chemical sensor platform.