Nasha Emieza Ruhaizat

Ms. Nasha Emieza Ruhaizat

Universiti Tun Hussein Onn Malaysia, Batu Pahat, Johor, Malaysia
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 September 2022 in Metals
Verified
Journal Article
Open access
PDF file
NRNasha Emieza Ruhaizat
Nasha Emieza Ruhaizat
NYNur Kamilah Yusuf
Nur Kamilah Yusuf
MLMOHD AMRI LAJIS
MOHD AMRI LAJIS
SASAMI AL-ALIMI
SAMI AL-ALIMI
BSBIN Shamsudin
BIN Shamsudin
WZWenbin Zhou
Wenbin Zhou
The current practice in aluminum recycling plants is to change the waste into molten metal through the conventional recycling (CR) manufacturing process. However, the CR technique is so energy-intensive that it also poses an indirect threat to the environment. This paper presents a study on meltless direct recycling hot press forging (DR-HPF) as an alternative sustainable approach that has fewer steps with low energy consumption, as well as preventing the generation of new waste. A laboratory experiment was conducted to study the mechanical properties and surface integrity of AA7075 aluminum alloy by employing a hot press forging (HPF) process under different temperatures (380, 430, and 480 °C) and holding times (0, 60, and 120 min). It was found that as the parameter increased, there was a positive increase in ultimate tensile strength (UTS), elongation to failure (ETF), density, and microhardness. The recycled chips exhibit the best mechanical properties at the highest parameters (480 °C and 120 min), whereas the UTS = 245.62 MPa and ETF = 6.91%, while surface integrity shows that the calculated microhardness and density are 69.02 HV and 2.795 g/cm3, respectively. The UTS result shows that the highest parameters of 480 °C and 120 min are comparable with the Aerospace Specification Metals (ASM) Aluminum AA7075-O standard. This study is a guide for machinists and the manufacturing industry to increase industry sustainability, to preserve the earth for future generations.

19 February 2021
Verified
Book Chapter
Closed access
PDF file
NRNasha Emieza Ruhaizat
Nasha Emieza Ruhaizat
NYNur Kamilah Yusuf
Nur Kamilah Yusuf
MLMOHD AMRI LAJIS
MOHD AMRI LAJIS
AMA. K. Mazlan
A. K. Mazlan
AMA. A. Muktari
A. A. Muktari
AAAzlan Ahmad
Azlan Ahmad

28 February 2021 in International Journal of Integrated Engineering
Verified
Journal Article
Closed access
NRNasha Emieza Ruhaizat
Nasha Emieza Ruhaizat
AAA.R. Ainuddin
A.R. Ainuddin
ZKZ. Kamdi
Z. Kamdi
The properties of Zinc Oxide (ZnO) such as broad direct band gap (3.37eV), good crystallinity and inexpensive materials had gain interest of many researchers. This project is prone to investigate the role of growth solution in the formation of ZnO structures. The objective of this project is to growth the ZnO hexagonal rods structure on the seed layer coated glass substrate and to investigate the influence of ZNH and HMT precursor on structural and morphological properties by varying its molar ratio. Firstly, the ZnO were coated on the microscope glass substrate for five layers using sol gel spin coating techniques. The dimension of the microscope glass substrate used were 2.5cm x 2.5cm. The ZnO seed layer coated substrates then undergo low cost hydrothermal method for the growth of ZnO structures. Different concentration of ZNH:HMT growth solution were used during hydrothermal method at molar ratio 1:1, 1:2 and 2:1 so that the influence of HMT and ZNH in the formation of ZnO structures can be further investigate. Several types of machine were used for the characterization properties of ZnO structures such as X-ray diffraction spectrophotometer (XRD), field emission scanning electron microscopy (FESEM), and energy dispersive x-ray spectroscopy (EDS). XRD analysis revealed that the ZnO samples exhibited hexagonal rods structure. The higher concentration of HMT shows higher intensity of diffraction peaks at the plane (101), (100) and (002) of ZnO structures. FESEM images showed that uneven size of ZnO structure at higher ZNH concentration while large size of ZnO structures can be seen at higher HMT concentration. EDS proved that the elemental composition of Zn and O do exist in the sample.