The combined steam/dry reforming (S/DR) technology was used to produce syngas from clean biogas. In the reaction conditions proposed, the catalytic bed can produce, without deactivation, a syngas with a H2/CO ratio of ≈2 directly processable for methanol or Fischer–Tropsch syntheses. Starting from the laboratory data obtained in the industrial conditions, mass and energy balances for the overall process were obtained from Aspen HYSYS simulations. The environmental evaluation was performed by applying the life cycle assessment (LCA) methodology, comparing different scenarios to the current industrial route to produce syngas (autothermal reforming or ATR of natural gas). The analysis showed that clean biogas-to-syngas technology using reforming processes has the potential to reduce the anthropogenic impact on the environment. The ReCiPe method showed that when the combined S/DR process is conducted using clean biogas also as a heat source, the CO2 balance turns negative, ensuring that the whole process has excellent potential as carbon capture and utilization (CCU) technology providing the lowest damage in all categories. Its improvement would make it possible to further reduce the environmental burden of the overall process, which is essential for achieving sustainable development.
Clean biogas, produced by anaerobic digestion of biomasses or organic wastes, is one of the most promising substitutes for natural gas. After its purification, it can be valorized through different reforming processes that convert CH4 and CO2 into synthesis gas (a mixture of CO and H2). However, these processes have many issues related to the harsh conditions of reaction used, the high carbon formation rate and the remarkable endothermicity of the reforming reactions. In this context, the use of the appropriate catalyst is of paramount importance to avoid deactivation, to deal with heat issues and mild reaction conditions and to attain an exploitable syngas composition. The development of a catalyst with high activity and stability can be achieved using different active phases, catalytic supports, promoters, preparation methods and catalyst configurations. In this paper, a review of the recent findings in biogas reforming is presented. The different elements that compose the catalytic system are systematically reviewed with particular attention on the new findings that allow to obtain catalysts with high activity, stability, and resistance towards carbon formation.
The combined steam/dry reforming of clean biogas (CH4/CO2 = 50/50 v/v) represents an innovative way to produce synthesis gas (CO + H2) using renewable feeds, avoiding to deplete the fossil resources and increase CO2 pollution. The reaction was carried out to optimize the reaction conditions for the production of a syngas with a H2/CO ratio suitable for the production of methanol or fuels without any further upgrading. Ni-Rh/Mg/Al/O catalysts obtained from hydrotalcite-type precursors showed high performances in terms of clean biogas conversion due to the formation of very active and resistant Ni-Rh bimetallic nanoparticles. Through the utilization of a {Ni10Rh(CO)19}{(CH3CH2)4N}3 cluster as a precursor of the active particles, it was possible to promote the Ni-Rh interaction and thus obtain low metal loading catalysts composed by highly dispersed bimetallic nanoparticles supported on the MgO, MgAl2O4 matrix. The optimization of the catalytic formulation improved the size and the distribution of the active sites, leading to a better catalyst activity and stability, with low carbon deposition with time-on-stream.
In recent years, the upgrading of lignocellulose bio-oils from fast-pyrolysis by means of ketonization has emerged as a frontier research domain to produce a new generation of biofuels. Propionic acid (PA) ketonization is extensively investigated as a model reaction over metal oxides, but the activity of other materials, such as metal phosphates, is mostly unknown. Therefore, PA ketonization was preliminarily investigated in the gas phase over both phosphates and oxides of Al, Zr, and La. Their catalytic activity was correlated to the physicochemical properties of the materials characterized by means of XRD, XRF, BET N2 porosimetry, and CO2- and NH3-TPD. Noteworthy, monoclinic ZrO2 proved to be the most promising candidate for the target reaction, leading to a 3-pentanone productivity as high as 5.6 h−1 in the optimized conditions. This value is higher than most of those reported for the same reaction in both the academic and patent literature.
21 December 2023 in Asian Journal of Organic Chemistry
This review highlights the advances in the synthesis of morpholine building blocks useful for artificial oligomers synthesis and peptide foldamers or biopolymers. Both morpholino nucleosides and morpholine derived from amino acids have been considered focusing on the preparation of antisense strands, peptides and bio‐based materials.