Omar Mohd Faizan Marwah

Prof. Omar Mohd Faizan Marwah

Universiti Tun Hussein Onn Malaysia, Batu Pahat, Johor, Malaysia

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2017 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
MHMohd Yussni Hashim
Mohd Yussni Hashim
AAAzriszul Mohd Amin
Azriszul Mohd Amin
OMOmar Mohd Faizan Marwah
Omar Mohd Faizan Marwah
MOMohd Hilmi Othman
Mohd Hilmi Othman
MYMohd Radzi Mohamed Yunus
Mohd Radzi Mohamed Yunus
NHNg Chuan Huat
Ng Chuan Huat
Alkali treatment was known as one commonly used treatment for natural fiber and obtained a good fiber matrix adhesion, thermal and mechanical properties of composite. This paper reports the effect of alkali treatment conditions on the physical properties of kenaf fiber such as density, weight loss, diameter, cross sectional and fiber morphology. In this study, kenaf fiber were treated under various conditions alkali concentration at 2, 6 and 10 (w/v%), immersion duration at 30, 240 and 480 minute and immersion temperature at 27, 60 and 100 o C. The effects of alkali treatment on kenaf fiber physical properties under various conditions were explored. Alkali treatment conditions setting have an impact on kenaf bast fiber physical characteristics. In kenaf fiber density, it was found that a small increase of kenaf density value after alkali treatment compared to untreated kenaf fiber. When each of alkali treatment parameters increased, kenaf fiber density also increased slightly. Kenaf fiber weight loss also exhibit a similar pattern of small increment with the increase of treatment parameters. Additionally, kenaf fiber diameter and cross sectional area show a decline pattern after treated with alkali. Furthermore, this decline pattern was corresponding with the increasing level of alkali treatment parameters. The maximum of kenaf diameter reduction was recorded at high level of each alkali treatment parameters.

1 March 2016 in Flow Measurement and Instrumentation
Verified
Journal Article
Closed access
EME.J. Mohamad
E.J. Mohamad
RRR.A. Rahim
R.A. Rahim
MRMohd Hafiz Fazalul Rahiman
Mohd Hafiz Fazalul Rahiman
HAH.L.M. Ameran
H.L.M. Ameran
SMS.Z.M. Muji
S.Z.M. Muji
OMOmar Mohd Faizan Marwah
Omar Mohd Faizan Marwah

14 August 2017 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
NNNurul Amira Binti Nordin
Nurul Amira Binti Nordin
MJMuhammad Akmal Bin Johar
Muhammad Akmal Bin Johar
MIMohd Halim Irwan Bin Ibrahim
Mohd Halim Irwan Bin Ibrahim
OMOmar Mohd Faizan Marwah
Omar Mohd Faizan Marwah
In today's technology, additive manufacturing has evolved over the year that commonly known as 3D printing. Currently, additive manufacturing have been applied for many industries such as for automotive, aerospace, medical and other commercial product. The technologies are supported by materials for the manufacturing process to produce high quality product. Plus, additive manufacturing technologies has been growth from the lowest to moderate and high technology to fulfil manufacturing industries obligation. Initially from simple 3D printing such as fused deposition modelling (FDM), poly-jet, inkjet printing, to selective laser sintering (SLS), and electron beam melting (EBM). However, the high technology of additive manufacturing nowadays really needs high investment to carry out the process for fine products. There are three foremost type of material which is polymer, metal and ceramic used for additive manufacturing application, and mostly they were in the form of wire feedstock or powder. In circumstance, it is crucial to recognize the characteristics of each type of materials used in order to understand the behaviours of the materials on high temperature application via additive manufacturing. Therefore, this review aims to provide excessive inquiry and gather the necessary information for further research on additive material materials for high temperature application. This paper also proposed a new material based on powder glass, which comes from recycled tempered glass from automotive industry, having a huge potential to be applied for high temperature application. The technique proposed for additive manufacturing will minimize some cost of modelling with same quality of products compare to the others advanced technology used for high temperature application.

29 March 2012 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
EMElmy Johana Mohamad
Elmy Johana Mohamad
HRHerlina Abdul Rahim
Herlina Abdul Rahim
PLP.L. Leow
P.L. Leow
MRMohd Hafiz Fazalul Rahiman
Mohd Hafiz Fazalul Rahiman
OMOmar Mohd Faizan Marwah
Omar Mohd Faizan Marwah
FYF.R. Mohd Yunus
F.R. Mohd Yunus

30 October 2017 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
RHR. H. A. Haq
R. H. A. Haq
KKK. Rd. Khairilhijra
K. Rd. Khairilhijra
MWM.S. Wahab
M.S. Wahab
NSN. Sa’ude
N. Sa’ude
MIM. Ibrahim
M. Ibrahim
SAS. Adzila
S. Adzila
In this study, Polycaprolactone / Polylactice Acid (PCL/PLA) composite are used to fabricate filament wire with the specific diameter, which is in the range of 1.75 to 1.80 mm. Full factorial experimental design technique was used to study the main effects and the interaction effects between operational parameter which is (A) die temperature, (B) roller puller speed, (C) spindle speed and (D) inlet temperature. Besides that, there are two levels (-1 and +1) and the response are filament wire diameter. There are 16 numbers of runs and plus 8 centre points per blocks which makes the runs into 24 runs. From the experiment it shows that there are four factor that are significant effects on the filament wire diameter which is A, B, C and BC. The optimum parameter setting are also determined and there are 10 suggestions to achieve the target with different setting of parameter. The margin error for confirmation run is below than 15% when the parameter set at 6 Hz spindle speed, 4.99 rpm roller puller, 100.31 °C die temperature and 79.65 °C inlet temperature which can be noted that the confirmation run result is acceptable. The optimization parameter setting can use to continue in Fused Deposition Modelling (FDM). Filament wire from PCL/PLA are succesfully fabricated with acceptable diameter size and ready to be used for Fused Depotion Modelling process (FDM).

1 January 2019 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
OMOmar Mohd Faizan Marwah
Omar Mohd Faizan Marwah
NYN F Yahaya
N F Yahaya
ADA Darsani
A Darsani
EME J Mohamad
E J Mohamad
RHR H A Haq
R H A Haq
MOM H Othman
M H Othman