The construction industry, being labor-intensive, prioritizes productivity to boost project performance, yet struggles to achieve expected levels despite increased focus by scholars and practitioners. This lagging causes significant losses in time, cost, and quality performance of construction projects but also broader implications for resource efficiency and environmental impacts. As a remedy to the multifaceted issue, this study aims to identify and evaluate life cycle risks of productivity management in construction projects in Türkiye. A comprehensive literature review identified risk factors affecting labor productivity, followed by a discussion session to finalize the decision framework, including life cycle phases of productivity management and risk factors in each phase. Then, the fuzzy analytical hierarchy (AHP) process revealed the most critical risk factors in each phase, followed by semi-structured interviews to reveal measures for addressing the most significant risks. The findings show that productivity management in construction projects contains nine phases. In addition, the most important factors were chiefly related to collaboration, information sharing, lack of supervision, work interruptions, and changes. Findings from semi-structured interviews emphasize regular employee training and open communication to enhance project outcomes, optimize workflows, and promote sustainability. The study’s key contribution is introducing a life cycle approach to construction productivity management, a previously unexplored perspective. This provides an effective framework that can be implemented in construction projects to manage and improve labor productivity as a whole-life cycle approach.
In Turkey, flexible pavement containing bituminous material is widely preferred on highways. Rigid pavement, which is based on concrete, is generally used in small-scale, specific projects. This situation, which has arisen due to historical and technical reasons, has also brought with it certain prejudices against rigid pavement applications. A review of the literature reveals that many factors influence the choice of highway pavement type, but decision-makers tend to make their selection based on the most important factors, disregarding other parameters. The lack of a systematic factor analysis is a shortcoming in this regard. In this research, a combined multi-criteria decision-making study was conducted, including the neglected factors, to address this technical deficiency in the pavement type selection process. Through detailed analysis, parameters likely to influence pavement type selection were identified and analyzed using the hybrid AHP-TOPSIS approach, guided by the opinions of experts in the field. The analysis shows that comfort (user ride quality), financial, and environmental factors are the most effective main criteria, while maintenance and repair costs, eco-friendliness, and initial construction costs were identified as the most critical sub-criteria influencing the choice of pavement type. Based on the analysis results, a detailed decision support system was presented to decision-makers according to the characteristics of the alternatives obtained. The results highlight the need for decision-making frameworks that prioritize both long-term cost efficiency and user safety, contributing to more sustainable and resilient pavement applications.
2 August 2024 in Engineering Science and Technology, an International Journal
Many cities in Türkiye have been affected by the devastating twin earthquakes in Kahramanmaraş. Following the Kahramanmaraş earthquakes, a field study was conducted to investigate the material characteristics of concrete used in collapsed buildings. The study’s major aim is to examine several parameters of reinforced concrete structures by comparing the samples taken from different locations in the region after the Kahramanmaraş Earthquakes for post-earthquake material characterization. Investigating the effect of concrete damage in these earthquakes, which especially affected 11 provinces and an area wider than approximately 100 thousand square kilometers, is of greater importance. For this purpose, Schmidt hammer measurements were carried out on structural elements, and concrete samples were collected from the same structures. Compression tests were conducted on the collected 21 samples taken from the 25 residential buildings to determine the mechanical properties of concrete such as compressive strength, modulus of elasticity, and Poisson’s ratio. Also, microstructural investigations were conducted on the concrete samples. The results showed that concrete samples had generally low strength and low deformation ability causing brittle failure of structures. When the compressive strengths of the concrete samples taken by the core drilling method were examined, it was determined that the results were between 4 MPa and 41 MPa, while the average compressive strength result was 16.7 MPa and the standard deviation was 8.6 MPa. Additionally, compressive strength results over 20 MPa were determined in 5 samples. The elasticity modules of the samples with compressive strength results above 15 MPa are higher than the value found in the equation given in TS500, while the others are lower. The elasticity modulus results were more compatible with the equation given in Eurocode. In addition, although there is no full agreement between the results obtained from Schmidt hammer measurements and the core drilling method results, the non-destructive method helps to find the weakest element on any floor. It can be concluded that there is a connection between the quality of concrete and the performance of buildings under severe earthquakes. Therefore, it is recommended to improve building codes, strengthen the inspection procedures, detail the quality control mechanisms, and sustain education/training programs to increase the resilience of the buildings in future earthquakes.
5 September 2024 in Computer and Decision Making (COMDEM)
A new perspective is available for the relationship between transportation systems and property prices, “evaluation by considering bandwidths”. The term “bandwidth” indicates the number of neighbor data points having an influence on the target point. The main motivation of this research is eliminating the restricted effects of a spatial analysis. When a single bandwidth value is defined for all models, indicate that an equal number of neighbor data in GWR influences all factors of the model for target points. When the multiscale geographically weighted regression (MGWR) is used, a unique bandwidth value can be defined for each factor. This study, by using MGWR, provides researchers the ability of distinguishing the effects of factors and classifying them as either wide-range or narrow-range. A total of 3487 geographical data were collected for a study area covering Esenyurt and Beylikduzu Counties in Istanbul, Turkey. As a result, when considering different bandwidths, factors are indeed recognized as either narrow-range or wide-range. The output of this study proved that the researchers are strongly recommended considering the bandwidth effects while performing a spatial regression analysis. Hence, the gap in the selection of factors for spatial analyses in different study areas is likely to be fulfilled.
13 September 2023 in International Journal of Pavement Research and Technology
A paratransit system is a public transportation mode, commonly operated by private transportation enterprises. In many countries, minibuses are considered paratransit systems and are often criticized for their inability to integrate with smart fare payment systems. Their revenue model is competitive, so it creates security vulnerabilities, and their sustainable service quality, which lags behind other modes of transport in terms of driving characteristics and transport system integration, is a significant disadvantage that sets minibuses apart from other modes of transport. However, given society’s usage habits, minibuses emerge as an indispensable mode of mobility, especially in certain areas and for specific individuals. This situation shows that minibuses need to be made infrastructure-compatible and controllable. This study examines the applicability of smart fare payment systems in minibuses using a multi-criteria evaluation framework. And it considers economic, technological, operational, and legal criteria holistically. Within the scope of the study, a pilot application was evaluated using AHP and TOPSIS techniques, comparing the cash-based structure with the option of using a smart fare payment system from the operators’ perspective. Thus, the system’s transformation potential was analytically assessed. The findings indicate that adopting a smart fare payment infrastructure is perceived to improve sustainable service quality, strengthen control mechanisms, and support revenue transparency.