This study describes and demonstrates key steps in a carbon-negative process for manufacturing cement from widely abundant seawater-derived magnesium (Mg) feedstocks. In contrast to conventional Portland cement, which starts with carbon-containing limestone as the source material, the proposed process uses membrane-free electrolyzers to facilitate the conversion of carbon-free magnesium ions (Mg 2+ ) in seawater into magnesium hydroxide [Mg(OH) 2 ] precursors for the production of Mg-based cement. After a low-temperature carbonation curing step converts Mg(OH) 2 into magnesium carbonates through reaction with carbon dioxide (CO 2 ), the resulting Mg-based binders can exhibit compressive strength comparable to that achieved by Portland cement after curing for only 2 days. Although the proposed “cement-from-seawater” process requires similar energy use per ton of cement as existing processes and is not currently suitable for use in conventional reinforced concrete, its potential to achieve a carbon-negative footprint makes it highly attractive to help decarbonize one of the most carbon-intensive industries.
1 May 2022 in Journal of Materials in Civil Engineering
In this study, the potential to directly use magnesium hydroxide as an alternative binder was investigated. A compaction molding technique was employed, where magnesium hydroxide powder was mixed with water at relatively low water-to-binder ratios, compacted in a mold, then subjected to accelerated curing at room temperature to form a carbonate binder. The influence of water-to-binder ratio and compaction pressure on the mechanical and microstructural properties of compacted magnesium hydroxide systems under accelerated curing was evaluated. Results showed that compaction pressure and water-to-binder ratio have a significant effect on uptake and strength development. An optimum compaction level was found to be 3 MPa in this study, where compressive strengths of and were reached after 2 and 5 days of curing. Results highlight the potential to tailor the mechanical properties of magnesium hydroxide systems through processing, and to reach strengths comparable to those of magnesium oxide systems but with the advantage of skipping the calcination step and reducing water demand.
2 August 2024 in Engineering Science and Technology, an International Journal
Many cities in Türkiye have been affected by the devastating twin earthquakes in Kahramanmaraş. Following the Kahramanmaraş earthquakes, a field study was conducted to investigate the material characteristics of concrete used in collapsed buildings. The study’s major aim is to examine several parameters of reinforced concrete structures by comparing the samples taken from different locations in the region after the Kahramanmaraş Earthquakes for post-earthquake material characterization. Investigating the effect of concrete damage in these earthquakes, which especially affected 11 provinces and an area wider than approximately 100 thousand square kilometers, is of greater importance. For this purpose, Schmidt hammer measurements were carried out on structural elements, and concrete samples were collected from the same structures. Compression tests were conducted on the collected 21 samples taken from the 25 residential buildings to determine the mechanical properties of concrete such as compressive strength, modulus of elasticity, and Poisson’s ratio. Also, microstructural investigations were conducted on the concrete samples. The results showed that concrete samples had generally low strength and low deformation ability causing brittle failure of structures. When the compressive strengths of the concrete samples taken by the core drilling method were examined, it was determined that the results were between 4 MPa and 41 MPa, while the average compressive strength result was 16.7 MPa and the standard deviation was 8.6 MPa. Additionally, compressive strength results over 20 MPa were determined in 5 samples. The elasticity modules of the samples with compressive strength results above 15 MPa are higher than the value found in the equation given in TS500, while the others are lower. The elasticity modulus results were more compatible with the equation given in Eurocode. In addition, although there is no full agreement between the results obtained from Schmidt hammer measurements and the core drilling method results, the non-destructive method helps to find the weakest element on any floor. It can be concluded that there is a connection between the quality of concrete and the performance of buildings under severe earthquakes. Therefore, it is recommended to improve building codes, strengthen the inspection procedures, detail the quality control mechanisms, and sustain education/training programs to increase the resilience of the buildings in future earthquakes.
Reactive MgO cement can substitute Portland cement in constructions for numerous purposes. While hydration of MgO yields a low-strength material, incorporation of additives, CO2 and heat curing can improve strength development. This study highlights how curing conditions and additives affect reactive MgO cements under elevated temperatures, providing key insights for enhancing sustainable construction materials with lower carbon footprints. Therefore, mortar mixtures were carbonated in a CO2 incubator for 3–14 days utilizing reactive MgO cement as a binder. Sodium carbonate and sodium bicarbonate were separately incorporated into mixtures to investigate their influence on compressive strength and microstructure. Elevated temperatures were also tested on carbonated magnesium-based material. Carbon dioxide curing enhanced compressive strengths and the reference carbonated group reached 20.1 MPa at the 14th day of curing. Sodium carbonate reduced the hydration rate and compressive strength, while air-cured mortar with sodium carbonate solution had the lowest compressive strength. However, sodium bicarbonate increased the strength of air-cured specimens. The specimens heated to 50 °C demonstrated a 35% increase in compressive strength, while temperatures of 100 °C or above led to a decline in strength. Hydration of MgO produced brucite and carbonation formed dypingite in the specimens’ microstructure. Temperature rise led to the disintegration of dypingite and rthe reappearanceof MgO.
The relation between crack growth and reduction in the compressive strength after high temperature exposure and after air re-curing was investigated in this study. Concrete specimens were heated to 1000 ºC and they were subjected to air re-curing for 28 days. During re-curing period, their heated surfaces were monitored by using a digital single-lens reflex camera and the images were analyzed by using image analysis software. After cooling, the maximum reduction in the compressive strength of concrete was 49.5% and that of air re-cured concrete was 66.8%. Image analyses showed high correlations between crack growth and reduction in the compressive strength. This non-destructive method has the potential to represent the extent of damage in concrete after high temperature exposure. Keywords: high temperature; fiber reinforced concrete; deterioration; crack development; black pixel analysis.
15 September 2025 in Black Sea Journal of Engineering and Science
Enerjiye olan talep her geçen gün arttığı için enerji kullanımını daha sürdürülebilir hale getirmek adına çalışmalar ve yönetmelikler yapılmaktadır. Binaların ısıtma ve soğutma enerjisi ihtiyacının karşılanması ciddi kaynak tüketimine ve çevresel sorunlara sebep olmaktadır. Bu sebeple binaların ısıtma ve soğutma enerjisi tüketiminin daha verimli ve sürdürülebilir olması için TS 825 – Binalarda Isı Yalıtımı Kuralları Standardı 2024 tarihinde güncellenmiştir. Son güncellemeyle yalıtım projelerine soğutma enerjisi talebi de dahil edilmiş olup bina zarfının renk koyuluğunun güneş enerjisi kazançları hesaplarında dikkate alınması istenmiştir. Bu çalışmada opak elemanların renk tercihinin bina enerji tüketimi üzerindeki etkilerinin incelenmesi hedeflenmiştir. Bunun için İzmir’deki ve Ankara’daki iki özdeş binanın farklı renk koyuluğu kombinasyonundaki yıllık ısıtma ve soğutma enerjisi talepleri hesaplanmıştır. Sonuçlar bina zarfının renk tonundaki koyulaşmanın toplam yıllık enerji tüketimini sıcak bölgede % 9,3’e kadar artırdığını göstermiştir. Renk koyulaşması ile soğutma enerjisi talebinin ısıtma enerjisindeki talebe göre daha çok arttığı anlaşılmıştır. Ayrıca duvar yüzeylerindeki renk koyulaşmasının çatı örtüsündeki renk koyulaşmasına göre enerji talepleri üzerinde daha belirgin bir etkisi olduğu görülmüştür.