Jude Osara

Dr. Jude Osara

Department of Mechanics of Solids, Surfaces and Systems, University of Twente, 7522 NB Enschede, The Netherlands
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 July 2019 in Entropy
Verified
Journal Article
Open access
PDF file
Jude OsaraJude Osara
Jude Osara
Michael BryantMichael Bryant
Michael Bryant
Formulated is a new instantaneous fatigue model and predictor based on ab initio irreversible thermodynamics. The method combines the first and second laws of thermodynamics with the Helmholtz free energy, then applies the result to the degradation-entropy generation theorem to relate a desired fatigue measure—stress, strain, cycles or time to failure—to the loads, materials and environmental conditions (including temperature and heat) via the irreversible entropies generated by the dissipative processes that degrade the fatigued material. The formulations are then verified with fatigue data from the literature, for a steel shaft under bending and torsion. A near 100% agreement between the fatigue model and measurements is achieved. The model also introduces new material and design parameters to characterize fatigue.

16 August 2022 in Tribology Transactions
Verified
Journal Article
Open access
PSPramod Shetty
Pramod Shetty
RMRobert Jan Meijer
Robert Jan Meijer
Jude OsaraJude Osara
Jude Osara
PLPiet Lugt
Piet Lugt
Presented in this article is a new method to measure the film thickness in a rolling bearing running under starved conditions, such as in grease-lubricated bearings, using the electrical capacitance method. The method was used to study the impact of speed on film thickness. Results show that fully flooded conditions prevail at lower speeds where the film thickness increases with increasing speed. At higher speeds, where grease-lubricated bearings run under starved lubrication conditions, this increase is less pronounced. At even higher speeds, the film thickness becomes almost independent of the speed.

3 April 2019 in Inventions
Verified
Journal Article
Open access
PDF file
Jude OsaraJude Osara
Jude Osara
Michael BryantMichael Bryant
Michael Bryant
Presented is a lithium-ion battery degradation model, based on irreversible thermodynamics, which was experimentally verified, using commonly measured operational parameters. The methodology, applicable to all lithium-ion batteries of all chemistries and composition, combined fundamental thermodynamic principles, with the Degradation–Entropy Generation theorem, to relate instantaneous capacity fade (loss of useful charge-holding capacity) in the lithium-ion battery, to the irreversible entropy generated via the underlying dissipative physical processes responsible for battery degradation. Equations relating capacity fade—aging—to battery cycling were also formulated and verified. To show the robustness of the approach, nonlinear data from abusive and inconsistent battery cycling was measured and used to verify formulations. A near 100% agreement between the thermodynamic battery model and measurements was achieved. The model also gave rise to new material and design parameters to characterize all lithium-ion batteries.

5 December 2022 in Tribology International
Verified
Journal Article
Open access
FHFemke Hogenberk
Femke Hogenberk
Jude OsaraJude Osara
Jude Osara
DEDirk van Den Ende
Dirk van Den Ende
PLPiet M. Lugt
Piet M. Lugt

7 March 2024 in Entropy
Verified
Journal Article
Open access
PDF file
Jude OsaraJude Osara
Jude Osara
MBMichael D. Bryant
Michael D. Bryant
Entropy generation, formulated by combining the first and second laws of thermodynamics with an appropriate thermodynamic potential, emerges as the difference between a phenomenological entropy function and a reversible entropy function. The phenomenological entropy function is evaluated over an irreversible path through thermodynamic state space via real-time measurements of thermodynamic states. The reversible entropy function is calculated along an ideal reversible path through the same state space. Entropy generation models for various classes of systems—thermal, externally loaded, internally reactive, open and closed—are developed via selection of suitable thermodynamic potentials. Here we simplify thermodynamic principles to specify convenient and consistently accurate system governing equations and characterization models. The formulations introduce a new and universal Phenomenological Entropy Generation (PEG) theorem. The systems and methods presented—and demonstrated on frictional wear, grease degradation, battery charging and discharging, metal fatigue and pump flow—can be used for design, analysis, and support of diagnostic monitoring and optimization.

22 January 2024 in Tribology International
Verified
Journal Article
Open access
PSPramod Shetty
Pramod Shetty
RMRobert Jan Meijer
Robert Jan Meijer
Jude OsaraJude Osara
Jude Osara
RPRihard Pasaribu
Rihard Pasaribu
PLPiet Lugt
Piet Lugt