Formulated is a new instantaneous fatigue model and predictor based on ab initio irreversible thermodynamics. The method combines the first and second laws of thermodynamics with the Helmholtz free energy, then applies the result to the degradation-entropy generation theorem to relate a desired fatigue measure—stress, strain, cycles or time to failure—to the loads, materials and environmental conditions (including temperature and heat) via the irreversible entropies generated by the dissipative processes that degrade the fatigued material. The formulations are then verified with fatigue data from the literature, for a steel shaft under bending and torsion. A near 100% agreement between the fatigue model and measurements is achieved. The model also introduces new material and design parameters to characterize fatigue.
Presented is a lithium-ion battery degradation model, based on irreversible thermodynamics, which was experimentally verified, using commonly measured operational parameters. The methodology, applicable to all lithium-ion batteries of all chemistries and composition, combined fundamental thermodynamic principles, with the Degradation–Entropy Generation theorem, to relate instantaneous capacity fade (loss of useful charge-holding capacity) in the lithium-ion battery, to the irreversible entropy generated via the underlying dissipative physical processes responsible for battery degradation. Equations relating capacity fade—aging—to battery cycling were also formulated and verified. To show the robustness of the approach, nonlinear data from abusive and inconsistent battery cycling was measured and used to verify formulations. A near 100% agreement between the thermodynamic battery model and measurements was achieved. The model also gave rise to new material and design parameters to characterize all lithium-ion batteries.
A generalization of the Degradation-Entropy Generation (DEG) theorem to multi-disciplinary multi-physics system-process analysis via a combination with pre-existing system models is presented in this article. Existing models and the DEG methodology are reviewed, and a method for evaluating degradation coefficients Bi is proposed. These coefficients characterize the system’s transformation based on active dissipative mechanisms, including temperature effects. The consistency of entropy generation in characterizing degradation is then inherited by these often-empirical system models, thereby rendering them more robust and applicable to similar systems without the need for numerous tests and measurements for model corrections. The approach applies to all systems and can quickly analyze and predict a system’s performance and degradation, even in the absence of experimental data (using known properties and material constants). Demonstrated applications herein include mechanically loaded systems (frictional wear, grease shearing, fatigue loading), electrochemical energy systems, thermal processes, and others.
19 December 2006 in IEEE Transactions on Magnetics
Insights from recovered armatures suggest re-examining historical modeling assumptions for railguns. The finite-element codes EMAP3D and DYNA3D were linked to explore the effects of temperature-dependent material properties, thermal diffusion, armature wear, inertial loading, thermal stresses, and 2-D model approximations. Temperatures and principal stresses for each of these cases were compared. Thermal diffusion and thermal stresses in armatures cannot be ignored past the first millisecond of launch; material properties under pulsed heating can significantly differ from equilibrium and room-temperature values. Armature wear and inertial loading can be ignored at low speeds, but not at high speeds (>1 km/s). Models in 2-D can approximate 3-D models with appropriate boundary conditions, but only for the first few milliseconds of launch. With a detailed EMAP3D model and minimal assumptions, simulations that agree within a few percentage points of microstructural measurements from recovered armatures are possible
Constitutive and dynamic relations for friction coefficient are presented. A first thrust combines the laws of thermodynamics to relate heat, energy, matter, entropy, and work of forces. The equation sums multiple terms—each with a differential of a variable multiplied by a coefficient—to zero. Thermodynamic considerations suggest that two variables, internal energy and entropy production, must depend on the others. Linear independence of differentials renders equations that yield thermodynamic quantities, properties, and forces as functions of internal energy and entropy production. When applied to a tribocontrol volume, constitutive laws for normal and friction forces, and coefficient of friction are derived and specialized for static and kinetic coefficients of friction. A second thrust formulates dynamics of sliding, with friction coefficient and slip velocity as state variables. Differential equations derived via Newton's laws for velocity and the degradation entropy generation (DEG) theorem for friction coefficient model changes to the sliding interface induced by friction dissipation. The solution suggests that the transition from static to kinetic coefficient of friction with respect to slip velocity for lubricant starved sliding is a property of the motion dynamics of sliding interacting with the dynamics of change of the surface morphology. Finally, sliding with stick-slip was simulated to compare this model to others.