This paper reports on a proposed novel 3D-printed sandwich lattice model using a triply periodic minimal surface (TPMS) structure for meta-functional composite bridge bearings (MFCBBs). It could be implemented in bridge systems, including buildings and railway bridges. A TMPS structure offers a high performance to density ratio under different loading. Compared to typical elastomeric bridge bearings with any reinforcements, the use of 3D-printed TPMS sandwich lattices could potentially lead to a substantial reduction in both manufacturing cost and weight, but also to a significant increase in recyclability with their better mechanical properties (compressive, crushing, energy absorption, vibration, and sound attenuation). This paper shows predictions from a numerical study performed to examine the behaviour of a TPMS sandwich lattice model under two different loading conditions for bridge bearing applications. The validation of the modelling is compared with experimental results to ensure the possibility of designing and fabricating a 3D-printed TPMS sandwich lattice for practical use. In general, the compressive experimental and numerical load–displacement behaviour of the TPMS unit cell are in excellent agreement within the elastic limit region. Moreover, its failure mode for bridge bearing applications has been identified as an elastic–plastic and hysteretic failure behaviour under uniaxial compression and combined compression–shear loading, respectively.
To a certain degree, composite railway sleepers and bearers have been recently employed as a replacement for conventional timber sleepers. Importantly, attributed to the rise in traffic demand, structural health monitoring of track structural members is essential to improve the maintenance regime and reduce risks imposed by any structural damage. A potential modern technique for detecting damage in railway components by using energy waves is called acoustic emission (AE). This technique has been widely used for concrete structures in other engineering applications, but the application for composites is relatively limited. Recently, fiber-reinforced foamed urethane (FFU) composites have been utilized as railway sleepers and bearers for applications in the railway industry. Neither does a design standard exist, nor have the inspection and monitoring criteria been properly established. In this study, three-point bending tests were performed together with using the AE method to detect crack growth in FFU composite beams. The ultimate state behaviors are considered to obtain the failure modes. This paper is thus the world’s first to focus on damage detection approaches for FFU composite beams using AE technology, additionally identifying the load-deflection curves of the beams. According to the experimental results, it is apparent that the failure modes of FFU composite beams are likely to be in brittle modes. Through finite element method, the results were in good agreement with less than 0.14% discrepancy between the experimental and numerical data. The attractive insights into an alternative technique for damage assessment of the composite components will help railway engineers to establish structural monitoring guidelines for railway composite sleepers and bearers.
Dynamic behaviors of composite railway sleepers and bearers in railway switches and crossings are not well-known and have never been thoroughly investigated. In fact, the dynamic properties of the full-scale composite sleepers and bearers are not available in practice. Importantly, the deteriorated condition or even the failure of composite materials and components in the railway system can affect the functional limitations or serviceability of the switches and crossings. Especially, it is important to identify the dynamic modal parameters of Fiber-reinforced Foamed Urethane (FFU) composite railway sleepers and bearers so that track engineers can adequately design and optimize the structural components with their superior properties, for benchmarking with the conventional sleepers and bearers. This paper is the world’s first to investigate the vibration characteristics of full-scaled FFU composite beams in healthy and damaged conditions, using the impact hammer excitation technique. This study also determines the dynamic elastic modulus of FFU composite beams from experimental dynamic measurements. It is found that the first bending mode in a vertical plane obviously is the first dominant mode of resonance under a free-free condition. The dynamic modal parameters reduce when damages occur. In this study, finite-element modeling has been used to establish a realistic dynamic model of the railway track incorporating FFU composite sleepers and bearers. Then, numerical simulations and experimental campaigns have been performed to enable new insights into the dynamic behaviors of composite sleepers and bearers. These insights are fundamental to the performance benchmarking as well as the development of vibration-based condition monitoring and inspection for predictive track maintenance.
This paper presents a novel meta-functional auxetic unit (MFAU) cell designed to improve performance and weight ratio for structural bridge bearing applications. Numerical investigations were conducted using three-dimensional finite element models validated by experimental results. The validated models were exposed to compression and buckling actions to identify structural failure modes, with special attention placed on the global behaviours of the meta-functional auxetic (MFA) composite bridge bearing. This bearing uses an unprecedented auxetic sandwich core design consisting of multiple MFAU cells. Numerical predictions of the elastic local critical buckling loads of the MFAU cell were in excellent agreement with both the analytical and experimental results, with an observed discrepancy of less than 1%. These results demonstrate that local buckling failures of MFAU cells can potentially be incurred prior to yielding under compression due to their slenderness ratios. Surprisingly, the designed sandwich core used in the MFA composite bridge bearing model can mimic an auxetic structure with significant crashworthiness, implying that this novel core composite structure can be tailored for structural bridge bearing applications. Parametric studies were thus carried out in order to enrich our insight into the MFA composite elements. These insights, stemming from both experimental and numerical studies, enable a novel design paradigm for MFAU that can significantly enhance the structural performance of MFA composite bridge bearings in practice.
Building Information Modelling (BIM) is a digitalisation tool that is widely adopted in construction industry. It is a three-dimensional digital replica of asset(s) such as buildings, which contain architectural information and building details (e.g. dimensions, materials, parts, and components). It has evolved from 2D CAD models (or blueprints) in the past to 3D CAD models embedded with information layers (e.g., construction time sequence or 4D-BIM), resulting in automation in construction. BIM has now been essential in various countries; for example, new UK BIM standards require asset owners to keep and maintain building information. BIM adopts an interoperable concept that can benefit the whole life-cycle assessment (LCA) and circularity of the built environments. Its applications extend to six dimensions (6D) where time sequence, cost and carbon footprint can now be reported in real time. These attributes are essential to stakeholders and critically help reduce any unexpected consumption and waste over the life cycle of a project. This study builds on the development of 6D BIM of an existing building to enrich circular value chains and stakeholder engagement. This paper highlights the development of 6D BIM, and, subsequently, the stakeholder interviews to address challenges, barriers, benefits, and effectiveness of 6D-BIM applications for stakeholder engagements across circular value chains. Snowballing sampling method has been used to identify stakeholder interviews to obtain new insights into the digital valorisation for stakeholder engagement. The outcome of this study will exhibit new insights and practical paradigms for BIM applications in built environments.
Bridge bearings are one of the most important components in bridge systems. Typical bearings are extensively used in small- to medium-span highway bridges since they are economical and offer a good performance at service-level conditions. On the other hand, common bridge bearings possess a low performance-to-weight ratio under combined compression and shear loading conditions (low crashworthiness and specific energy absorption), due to their heavy weight, high costs, and the non-recyclability of steel and elastomer materials. With the help of a relatively higher ratio of a 3D-printed triply periodic minimal surface (TPMS) structure, this method can potentially be used for bridge bearing applications. However, the cyclic responses of this TPMS structure used in bearings have never been completely investigated. This study is the world’s first to investigate the effects of normal pressure on the cyclic responses of novel 3D-printed TPMS bridge bearings. A numerical TPMS unit cell model considering the effects of normal pressure on cyclic responses of a novel TPMS bridge bearing is developed and validated with experimental data. The numerical results reveal new insights related to the nonlinear effects of normal pressure on the cyclic behaviours of 3D-printed TPMS bearings. Higher normal pressures result in a higher degree of nonlinearity in the dynamic cyclic responses of the 3D-printed TPMS bearings.
About Me
Pasakorn Sengsri is currently a PhD candidate at the University of Birmingham.
Pasakorn Sengsri is currently a PhD candidate at the University of Birmingham.