Philipp Höfer

Prof. Dr. Philipp Höfer

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 March 2023 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
JWJulius Westbeld
Julius Westbeld
FCFabio von Coburg
Fabio von Coburg
PHPhilipp Höfer
Philipp Höfer
Powder Bed Fusion (PBF) enables the production of complex geometries which offer the opportunity to manufacture lightweight, stiffness-optimised or integrally designed components. Although these properties are usually advantageous for the performance in many applications, they pose disadvantages under vibration as they lead to low damped components. These are prone to high vibration amplitudes which result in higher sound radiation and a reduced lifetime. Particle damping can counteract these disadvantages. By including cavities during the design process, unmelted powder remains inside the component after its production. This powder dissipates energy under vibration by inelastic impacts and friction in particle-particle or particle-wall-interactions, increasing the damping characteristics of the component. In this work, additively manufactured AlSi10Mg specimens with cavities are investigated with respect to their damping characteristics by experimental modal analysis. The focus of the investigation is on thin and flat cavities that can be easily integrated into components without adapting the external geometry. The damping characteristics in dependence on excitation amplitude and mode are quantified. The extent to which settling effects of the powder during shaking influence the damping is analysed. The vibration of the specimens is forced by an electrodynamic shaker and their response is measured contactlessly via Scanning Laser Doppler Vibrometry (SLDV). A damping effect of up to 564% depending on the mode, excitation amplitude and specimen can be achieved. In addition, a significant settling effect of the powder which hampers the damping effect is identified by CT scans and modal analysis.

3 April 2025 in Nanomaterials
Verified
Journal Article
Open access
PDF file
JBJohannes Bibinger
Johannes Bibinger
SESebastian Eibl
Sebastian Eibl
HGHans-Joachim Gudladt
Hans-Joachim Gudladt
BSBernhard Schartel
Bernhard Schartel
PHPhilipp Höfer
Philipp Höfer
Enhancing the thermal resistance of carbon fiber-reinforced polymers (CFRPs) with flame retardants or coatings often leads to increased weight and reduced mechanical integrity. To address these challenges, this study introduces an innovative approach for developing nanocomposites using carbon-based nanoparticles, while preserving the structural lightweight properties. For this, carbon black particles (CBPs) up to 10% and carbon nanotubes (CNTs) up to 1.5% were incorporated into the RTM6/G939 composite material. The obtained samples were then analyzed for their properties and heat resistance under one-sided thermal loading at a heat flux of 50 kW/m2. Results demonstrate that integrating these particles improves heat conduction without compromising the material’s inherent advantages. As a result, thermo-induced damage and the resulting loss of mechanical strength are delayed by 17% with CBPs and 7% with CNTs compared to the unmodified material. Thereby, the thermal behavior can be accurately modeled by a straightforward approach, using calibrated, effective measurements of the nanoparticles in the polymer matrix rather than relying on theoretical assumptions. This approach thus provides a promising methode to characterize and improve thermal resistance without significant trade-offs.

3 April 2025 in Advanced Manufacturing: Polymer & Composites Science
Verified
Journal Article
Open access
MTMatthias Taubert
Matthias Taubert
JDJörg Gregor Diez
Jörg Gregor Diez
BMBruno Musil
Bruno Musil
PHPhilipp Höfer
Philipp Höfer

7 October 2025 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
JWJulius Westbeld
Julius Westbeld
PHPhilipp Höfer
Philipp Höfer
This study investigates the damping behaviour of particle damping integrated into specimens produced via laser beam powder bed fusion (PBF-LB). The specimens, made from AlSi10Mg, contain internal cavities that remain filled with residual powder after manufacturing and dissipate vibrational energy through particle interactions. A systematic experimental investigation is conducted on specimens of varying lengths, cavity positions, and cavity volumes. The influence of relative cavity volume and modal displacement at the cavity location is combined into a single parameter and its direct relationship to the damping effect is demonstrated. Furthermore, the effectiveness of particle damping is shown to be strongly frequency-dependent: maximum effectiveness is observed in the resonance frequency range of 3–4 kHz, while significantly reduced damping occurs at lower frequencies. CT scans reveal that individual outlier specimens with a reduced packing density within the cavity exhibit a comparably high damping effect at lower frequencies but a low damping effect at higher frequencies. The presented metric enables direct comparison of damping behaviour across bending modes and specimen geometries, providing valuable guidelines for the implementation of frequency-tuned particle damping in PBF-LB components.

28 July 2022 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
EBErhard Buchmann
Erhard Buchmann
MEMichael Erdmann
Michael Erdmann
MKMathias Köberl
Mathias Köberl
PHPhilipp Höfer
Philipp Höfer
There is a growing interest in the application of thermoplastics and thermoplastic composites for lightweight structures, thus also in friction stir welding (FSW) as a suitable joining technology. With the transformation of FSW from metals to polymers, several new tooling concepts were developed; mainly various heating setups to add external thermal energy to the process were designed. However, current temperature control approaches do not consider the cooling of the process at high rotational speeds and the asymmetry of the process in thermomechanical conditions. In this paper, we present a stationary shoulder with fluid temperature control, which is also capable of cooling the process. Additionally, asymmetric temperature control conditions can be examined by applying different flow directions. For investigation, butt welds of PMMA sheets were welded and assessed using the weld morphology and tensile strengths. Different fluid temperatures, feed rates, and both flow directions were applied and led to different tensile strengths. It could be shown that the optimal control temperature is different for the advancing side (AS) and the retreating side (RS). By using a transverse flow, a heat transport from the warmer AS to the colder RS could be established, which improved the strength. Moreover, the tensile strength could be increased by cooling the process at a feed rate of 100 mm/min. To improve the effectiveness of the temperature control, a new shoulder with independent temperature-controlled areas is proposed.

19 August 2024 in Composites Part C: Open Access
Verified
Journal Article
Open access
PVPablo Vitale
Pablo Vitale
JMJoaquin Montero
Joaquin Montero
GFGaston Francucci
Gaston Francucci
HRHelmut Rapp
Helmut Rapp
KPKristin Paetzold
Kristin Paetzold
PHPhilipp Höfer
Philipp Höfer