Po-Hsu Chen

Dr. Po-Hsu Chen

Restorative Sciences, University of Alabama at Birmingham, Birmingham, Alabama, USA
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 August 2022 in Journal of Prosthodontics
Verified
Journal Article
Closed access
AKAmir Koujan
Amir Koujan
HAHimanshi Aggarwal
Himanshi Aggarwal
PCPo-Hsu Chen
Po-Hsu Chen
ZLZhaofei Li
Zhaofei Li
DGDaniel A. Givan
Daniel A. Givan
CFChin‐Chuan Fu
Chin‐Chuan Fu

4 August 2016 in Polymer Engineering & Science
Verified
Journal Article
Closed access
PDF file
MVMaría G. Villarreal‐Marroquín
María G. Villarreal‐Marroquín
PCPo-Hsu Chen
Po-Hsu Chen
RMRachmat Mulyana
Rachmat Mulyana
TSThomas J. Santner
Thomas J. Santner
ADAngela M. Dean
Angela M. Dean
JCJose Castro
Jose Castro

11 January 2024 in Materials
Verified
Journal Article
Open access
PDF file
PCPo-Hsu Chen
Po-Hsu Chen
EEEsra Elamin
Esra Elamin
AAAkram Sayed Ahmed
Akram Sayed Ahmed
DGDaniel A. Givan
Daniel A. Givan
CFChin-Chuan Fu
Chin-Chuan Fu
NLNathaniel Lawson
Nathaniel Lawson
Background: To determine what thickness of 5 mol% yttria zirconia (5Y-Z) translucent crowns cemented with different cements and surface treatments would have equivalent fracture resistance as 3 mol% yttria (3Y-Z) crowns. Methods: The study included 0.8 mm, 1.0 mm, and 1.2 mm thickness 5Y-Z (Katana UTML) crowns and 0.5 and 1.0 mm thickness 3Y-Z (Katana HT) crowns as controls. The 5Y-Z crowns were divided among three treatment subgroups (n = 10/subgroup): (1) cemented using RMGIC (Rely X Luting Cement), (2) alumina particle-abraded then luted with the same cement, (3) alumina particle-abraded and cemented using a resin cement (Panavia SA Cement Universal). The 3Y-Z controls were alumina particle-abraded then cemented with RMGIC. The specimens were then loaded in compression at 30° until failure. Results: All 5Y-Z crowns (regardless of thickness or surface treatment) had a similar to or higher fracture force than the 0.5 mm 3Y-Z crowns. Only the 1.2 mm 5Y-Z crowns with resin cement showed significantly similar fracture force to the 1 mm 3Y-Z crowns. Conclusion: In order to achieve a similar fracture resistance to 0.5 mm 3Y-Z crowns cemented with RMGIC, 5Y-Z crowns may be as thin as 0.8 mm. To achieve a similar fracture resistance to 1.0 mm 3Y-Z crowns cemented with RMGIC, 5Y-Z crowns must be 1.2 mm and bonded with resin cement.

30 September 2020 in Journal of Diagnostics and Treatment of Oral and Maxillofacial Pathology
Verified
Journal Article
Open access
John Minh LeJohn Minh Le
John Minh Le
PCPo-Hsu Chen
Po-Hsu Chen
JSJulius Seidenfaden
Julius Seidenfaden
AMAnthony Morlandt
Anthony Morlandt
MKMichael Kase
Michael Kase
Total rhinectomy defects pose a challenge for the reconstructive surgeon, but since the introduction of osseointegrated implants, maxillofacial implant–retained prosthetic rehabilitation has provided the patient with an alternative option that has an excellent cosmetic result. Traditionally, zygomatic implants are used for prosthodontic restoration in patients with severely atrophic maxilla or to retain an obturator after tumor ablative surgery. More recently, the nonconventional use of zygomatic implants for retention of a nasal prosthesis has been reported in cases involving rhinectomy defects where the length of conventional dental implants is a limiting factor. In this article, we describe the use and value of transversely-oriented zygomatic implants in combination with an acrylic keeper and maxillary denture to optimize retention of a complex, multi-unit prosthesis in an edentulous patient with a total rhinectomy and upper lip defect.

1 September 2021 in The Journal of Prosthetic Dentistry
Verified
Journal Article
Closed access
PCPo-Hsu Chen
Po-Hsu Chen
JSJulius C. Seidenfaden
Julius C. Seidenfaden
MKMichael T. Kase
Michael T. Kase
ISIradj Sooudi
Iradj Sooudi

14 November 2021 in Journal of Advanced Dentistry
Verified
Journal Article
Open access
PDF file
RARaghdah AlShaibani
Raghdah AlShaibani
TATaha M. Akhtar
Taha M. Akhtar
MGMarissa Gentle
Marissa Gentle
PCPo-Hsu Chen
Po-Hsu Chen
PLPeixi Liao
Peixi Liao
Objectives: Many patients with maxillofacial defects require maxillofacial prosthetic rehabilitation due to cancer, trauma, or congenital diseases. Adequate surgical and prosthetic treatment planning is required to achieve satisfactory morphological and functional results. Before computer-aided design/computer-assisted manufacture (CAD/CAM) technology was introduced, conventional methods have been used to reconstruct the facial form, which involved making impressions, obtaining models and fabricating the prosthesis all of which is time consuming and requires multiple visits. A rapid progress has been made with advances in digital technology, such as milling systems, rapid prototyping, three-dimensional (3D) scanning, and 3D printing, which has improved the patients’ expectations, the functional and esthetic treatment outcomes. Materials and methods: An electronic search was conducted in the Cochrane, PubMed (MEDLINE), and ScienceDirect databases between July 2000 and October 2020. A manual search was also performed to cover all digital aspects of the maxillofacial prosthesis. The inclusion criteria were randomized clinical trials, prospective or retrospective cohort, and cross-sectional studies performed on humans with at least 1 year of follow-up and published within the last 20 years. Results: The results showed that the used technologies in a digital workflow of auricular, orbital and nasal prosthesis reduce the manufacturing time and allow the manufacture of high-quality prostheses for missing facial parts. The methodology provides a good position for further development issues and is usable for clinical practice. Conclusion: Utilization of digital technologies in the facial prosthesis manufacturing process can be a good contribution for higher patient comfort and production efficiency but also comes with a higher initial investment and greater demands for experience with software tools.