Solar photovoltaic (PV) energy systems are one of the most widely deployed renewable technologies in the world. The efficiency of solar panels has been studied during the last few decades, and, to date, it has not been possible to displace the production of energy using crystalline silicon wafer-based technology whose efficiency has reached values around 26.1%. Moreover, using solar tracking PV systems has become a feasible alternative to increase the electric output of PV silicon technologies instead of using the conventional fixed PV installation on a flat or sloping surface. The following study has compared fixed and dual-axis sun-tracking PV panels in order to quantify the enhancement associated with the amount of energy harvested when using dual-axis tracking PV systems in the city of Manta, located in a coastal region of Ecuador. In order to carry out this study, an IoT monitoring system based on Raspberry Pi3 and Arduino platforms was used. Measurements of solar radiation (W/m2), light intensity (Lux), temperature (°C), short-circuit current (A), and open-circuit voltage (V) were taken every minute for both systems. The results prove that the dual-axis tracking PV system produces, on average, 19.62% more energy than the static PV system. These results present an 8.62% energy increase with respect to a previous study carried out in an equatorial region with similar characteristics to those of the city of Manta, where a one-axis tracking PV system was used.
Ecuador is grappling with a severe energy crisis, marked by frequent power outages. A recent study explored solar energy efficiency in the coastal city of Manta using an IoT real-time monitoring system to compare static photovoltaic (PV) systems with two single-axis solar tracking systems: one based on astronomical programming and the other using light-dependent resistor (LDR) sensors. Results showed that both tracking systems outperformed the static PV system, with net gains of 31.8% and 37.0%, respectively. The astronomical-programming-based system had a slight edge, operating its stepper motor intermittently for two minutes per hour, while the LDR system required continuous motor energization. The single-axis tracker using astronomical programming demonstrated notable advantages in energy efficiency and complexity, making it suitable for equatorial regions like Manta. The study also suggested potential further gains by adjusting solar positioning at shorter intervals, such as every 15 or 30 min. These findings enhance our understanding of solar tracking performance in equatorial environments, offering valuable insights for optimizing solar energy systems in regions with high solar radiation. By emphasizing customized solar tracking mechanisms, this research presents promising solutions to Ecuador’s energy crisis and advances sustainable energy practices.
19 May 2020 in Revista Arbitrada Interdisciplinaria Koinonía
La investigación tuvo por objetivo diseñar una estación meteorológica automática para registrar las variables solar y eólica. Se desarrolló desde la metodología de tipo descriptiva documental con diseño no experimental, lo cual, permitió en una primera fase, analizar datos meteorológicos con la finalidad de diagnosticar la necesidad de contar con el diseño de una propuesta de una estación meteorológica. Se observa que la radiación en este mes se osciló entre los 5.000 y 7.000 Wh/(m2-día), con algunas excepciones, llegando incluso a sobrepasar los 8.000 Wh/(m2-día). Es de notar que hubo días con una bajísima radiación solar dadas las lluvias y fuerte nubosidad encontradas en este mes. La estación meteorológica automática diseñada, evidencia una gran ventaja frente a las estaciones meteorológicas convencionales; esta puede ser usada en zonas con poca accesibilidad o en ausencia de red eléctrica.
Desde hace años la energía solar viene siendo motivo de estudio para la generación eléctrica como fuente de alimentación alternativa. El objetivo principal de este proyecto es realizar un análisis comparativo de la producción de energía eléctrica entre paneles fotovoltaicos fijos y con sistemas de seguimiento en un eje. Se diseño y construyó tres módulos solares con las mismas características técnicas, pero con diferentes sistemas de seguimiento solar; los sistemas seguidores de un eje utilizaron sistemas de seguimiento por programación astronómica y seguimiento de luz por sensores LDR. Se implementaron sensores de corriente, voltaje y temperatura, así como un software encargado de obtener las curvas características del comportamiento de la producción en cada prototipo. El procesamiento de los datos, así como la gestión de señales de E/S proveniente de los diferentes componentes electrónicos asociados al funcionamiento de cada sistema, son gobernados por una placa Arduino mega unida a un módulo ethernet con la finalidad de poder observar las curvas de producción desde un sitio web, todo esto operando de manera autómata. Por tanto, determinamos que el sistema FV por programación astronómica es el más conveniente, debido a su menor consumo energético al corregir la posición del panel.