Rikard Mäki

Dr. Rikard Mäki

Boliden (Sweden), Stockholm, Sweden
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 July 2022 in Energies
Verified
Journal Article
Open access
PDF file
LLLars Olof Lindgren
Lars Olof Lindgren
AGAnders Grauers
Anders Grauers
JRJonas Ranggård
Jonas Ranggård
RMRikard Mäki
Rikard Mäki
Transport of ore and overburden in open-pit mines is often performed with large haul trucks. Battery-electric operation of haul trucks can significantly reduce the CO2 emissions and the fossil fuel dependence of open-pit mining. This simulation study investigates the feasibility and economy of operating large haul trucks battery-electrically, charging from an electric road system in the form of overhead trolley lines. The used simulation model is verified against measurements on diesel-electric haul trucks in normal operation. The simulation model is then tested with five drive cycles representing typical operations in the Aitik copper mine in northern Sweden. This simulation study shows that battery-electric operation with an electric road is feasible. It is shown that battery-electric operation is much cheaper than diesel-electric operation under reasonable assumptions. It is also much cheaper than diesel-electric operation assisted by an electric road.

11 June 2021 in Minerals
Verified
Journal Article
Open access
PDF file
ASAndreas Svanberg
Andreas Svanberg
SLSimon Larsson
Simon Larsson
RMRikard Mäki
Rikard Mäki
Pär JonsénPär Jonsén
Pär Jonsén
Failure in industrial processes is often related to wear and can cause significant problems. It is estimated that approximately 1–4% of the gross national product for an industrialized nation is related to abrasive wear. This work aims to numerically predict development of wear for full-scale mining applications in harsh sub-arctic conditions. The purpose is to increase the understanding of wear development in industrial processes and optimize service life and minimize costs related to wear. In the present paper, a granular material model consisting of the discrete element method (DEM) and rigid finite element particles is utilized to study wear in full-scale mining applications where granular materials and steel structures are present. A wear model with the basis in Finnie’s wear model is developed to calculate wear from combined abrasive sliding and impact wear. Novel in situ full-scale experiments are presented for calibration of the wear model. A simulation model of the rope shovel loading process is set up where the bucket filling process is simulated several times, and the wear is calculated with the calibrated wear model. From the full-scale validation, it is shown that the simulated wear is in excellent agreement when compared to the experiments, both regarding wear locations and magnitudes. After validation, the model is utilized to study if wear can be minimized by making small changes to the bucket. One major conclusion from the work is that the presented wear simulator is a suitable tool that can be used for product development and optimization of the loading process.

20 May 2024 in Mining, Metallurgy & Exploration
Verified
Journal Article
Open access
PDF file
LCLiyuan Chi
Liyuan Chi
RYRiika M. Ylitalo
Riika M. Ylitalo
ZZZong-Xian Zhang
Zong-Xian Zhang
PBPekka Bergström
Pekka Bergström
SHSunniva Haugen
Sunniva Haugen
ASAnders Sand
Anders Sand
The effect of detonator placement on rock fragmentation by blasting was studied in the Kevitsa open-pit mine. Considering rock mass properties, explosives properties, and blast parameters, a comprehensive analysis of 37 production blasts confirms that the middle detonator yields finer fragmentation than the bottom detonator in the full range of investigated sizes. Meanwhile, using the LS-DYNA code, a bench model with a single blasthole was built in a three-dimensional setting. A single detonator placed at two different positions—the middle and bottom—of the explosive column was analyzed in this study. By analyzing principal stress states on the plane through the blasthole axial and vertical to the bench face, the numerical results show that the middle detonator creates a stress concentration area near the bench face characterized by triaxial tension, while the bottom detonator does not. Furthermore, the middle detonator generates a larger stress concentration area with biaxial tension near the bench face than the bottom detonator. Considering that triaxial and biaxial tensions are more favorable to fragmentation than uniaxial tension, it can be concluded from simulation results that these areas with triaxial tension and biaxial tension in the middle detonator are a significant factor contributing to achieving better fragmentation, compared to the bottom detonator. The middle detonator position has replaced the bottom detonator position in the Kevitsa mine.

23 May 2024 in Mining, Metallurgy & Exploration
Verified
Journal Article
Open access
PDF file
LCLiyuan Chi
Liyuan Chi
RYRiika M. Ylitalo
Riika M. Ylitalo
ZZZong-Xian Zhang
Zong-Xian Zhang
PBPekka Bergström
Pekka Bergström
SHSunniva Haugen
Sunniva Haugen
ASAnders Sand
Anders Sand