The design and management of infrastructure is a significant challenge for traffic engineers and planners. Accurate traffic characterization is necessary for effective infrastructure utilization. Thus, models are required that can characterize a variety of conditions and can be employed for homogeneous, heterogeneous, equilibrium and non-equilibrium traffic. The Lighthill-Whitham-Richards (LWR) model is widely used because of its simplicity. This model characterizes traffic behavior with small changes over a long idealized road and so is inadequate for typical traffic conditions. The extended LWR model considers driver types based on velocity to characterize traffic behavior in non lane discipline traffic but it ignores the stimuli for changes in velocity. In this paper, an improved model is presented which is based on driver reaction to forward traffic stimuli. This reaction occurs over the forward distance headway during which traffic aligns to the current conditions. The performance of the proposed, LWR and extended LWR models is evaluated using the first order upwind scheme (FOUS). The numerical stability of this scheme is guaranteed by employing the Courant, Friedrich and Lewy (CFL) condition. Results are presented which show that the proposed model can characterize both small and large changes in traffic more realistically. Doi: 10.28991/cej-2021-03091632 Full Text: PDF
Traffic-flow modelling has been of prime interest to traffic engineers and planners since the mid-20th century. Most traffic-flow models were developed for the purpose of characterizing homogeneous traffic flow. Some of these models are extended to characterize the complex interactions involved in heterogeneous traffic flow. Existing heterogeneous traffic-flow models do not characterize the driver behavior leading to gap filling in heterogeneous traffic conditions. This study aimed at explaining the gap-filling behavior in heterogeneous traffic flow by using the effusion model of gas particles. The driver’s behavior leading to gap filling in heterogeneous traffic was characterized through developing analogies between the traffic flow and the Maxwell–Boltzmann equation for effusion of gases. This model was subsequently incorporated into the Payne–Whitham (PW) model by replacing the constant anticipation term. The proposed model was numerically approximated by using Roe’s scheme, and numerical simulation of the proposed model was then carried out by using MATLAB. The results of the proposed and PW models were therefore compared. It is concluded that the new model proposed in this study not only produces better results compared to the PW model, but also better captures the expected reality. The main difference between the behavior of the two models is that the effect of bottleneck in the density of traffic is propagated in the form of a shockwave travelling backwards in time in the new model, while the PW model does not exhibit this effect.
Output-only modal analysis using ambient vibration testing is ubiquitous for the monitoring of structural systems, especially for civil engineering structures such as buildings and bridges. Nonetheless, the instrumented nodes for large-scale structural systems need to cover a significant portion of the spatial volume of the test structure to obtain accurate global modal information. This requires considerable time and resources, which can be challenging in large-scale projects, such as the seismic vulnerability assessment over a large number of facilities. In many instances, a simple center-line (stairwell case) topology is generally used due to time, logistical, and economic constraints. The latter, though a fast technique, cannot provide complete modal information, especially for torsional modes. In this research, corner-line instrumented nodes layouts using only a reference and a roving sensor are proposed, which overcome this issue and can provide maximum modal information similar to that from 3D topologies for medium-rise buildings. Parametric studies are performed to identify the most appropriate locations for sensor placement at each floor of a medium-rise building. The results indicate that corner locations at each floor are optimal. The proposed procedure is validated through field experiments on two medium-rise buildings.
In this paper, a seismic hazard assessment (SHA) of the Shigo Kas hydropower project has been performed by deterministic and probabilistic approaches. The previously developed MATLAB-based code has been used for deterministic SHA, incorporating local site effects through deep soil analysis. On the other hand, for probabilistic SHA, CRISIS 2007 has been used through diffuse areal source zones. The latest updated earthquake instrumental and historical catalogs have been developed. Based on the recommendations of the International Commission on Large Dams, peak ground acceleration (PGA) values for the maximum credible earthquake (MCE), safety evaluation earthquake (SEE), design basis earthquake (DBE) and operating basis earthquake (OBE) have been assessed, which are 0.50 g, 0.68 g, 0.35 g and 0.24 g, respectively, at the intake location, and 0.50 g, 0.61 g, 0.30 g and 0.22 g, respectively, at the powerhouse location. Hazard maps have been developed for scenario-based earthquakes (MCE) and for the peak ground acceleration of 145-, 475- and 2500-year return periods. The de-aggregation process has evaluated the combined effects of magnitude and distance. At a distance of 30 to 70 km from the earthquake source, earthquakes of magnitude 5 Mw to 5.6 Mw and 5.9 Mw to 6.5 Mw are more hazardous for the current project.
1 March 2016 in Insight - Non-Destructive Testing and Condition Monitoring