Samuel Estenlund

Dr. Samuel Estenlund

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2016
Verified
Conference Paper
Closed access
Samuel EstenlundSamuel Estenlund
Samuel Estenlund
MAMats Alakula
Mats Alakula
ARAvo Reinap
Avo Reinap
This literature review presents a summary of recent research about PM-less machines for electrical vehicles. Recently, IPM machines has proven to be very popular among electrical vehicle manufacturers. However, the neodymium permanent magnets being used are expensive and have a risk of rocketing the production cost of a machine if the price increases more. With this in mind, five PM-less machine topologies have been studied in recent literature. The topologies in question are synchronous reluctance machines, switched reluctance machines, double stator switched reluctance machines, electrically excited synchronous machines and induction machines. Their pros, cons and potential in the EV market are reviewed, coming to the conclusion that they have a potential for the EV market, depending on how demands and techniques are developed. It is concluded that synRMs are cheap and easy to control, while design and material choices are the greatest challenges for it meet the requirements. SRMs are robust and simple to manufacture, but noise and torque ripple reduction as well as design and materials needs more research. EESMs have a wide operation area with high efficiency, but larger losses for higher load, which makes cooling a challenge. IMs are mature and reliable, but control can be improved and some trade-offs in the design choices has to be dealt with.

19 June 2024
Verified
Conference Paper
Closed access
Samuel EstenlundSamuel Estenlund
Samuel Estenlund
EAErik Adolfsson
Erik Adolfsson
SHSeyed Hosseini
Seyed Hosseini
This work presents a literature study over how additive manufacturing can be used to improve the performance of windings for traction machines when it comes to materials, loss minimization and thermal management, especially for concentrated windings. It continues to present the additive manufacturing methods most suitable for additively manufacturing windings. The lessons from manufacturing coils with metal binder jetting are presented, concluding that some support structures are needed which can be chemically removed later in the process which means that the full detail capability of metal binder jetting can not be utilized fully. Finally different approaches to thermal management with additively manufactured coils are modelled. The results show that compared to direct air cooled windings, additively manufactured copper coils with direct cooling can increase the maximum current by 50 %. If aluminium (AlSiMg) windings are made with both additive manufacturing and improved end-turn cooling they can match the performance of non-AM direct air cooled copper windings.

1 September 2018
Verified
Conference Paper
Closed access
Samuel EstenlundSamuel Estenlund
Samuel Estenlund
This article presents a concept of direct cooled windings for electrical machines, pumping air through hollow rectangular copper windings. The thermal constraints pose a serious limitation in the performance of many applications of electrical machines, not least in electrical vehicles. The difference between temporary maximum output and continuous output is often substantial. This difference can be decreased with effective cooling methods, such as direct cooling of the windings. The concept of direct cooled windings are modeled in a empirical-lumped parameter model. The model is described in the article and experimentally validated through experiments. Finally the results of the model regarding optimized dimensions for electrical machines are presented and discussed. The results show that a current density of 16 A/mm 2 (insulation and cooling channels accounted for) can be achieved. 18 A/mm 2 is achievable with other dimensions, but with lower efficiency. The pump power for the coolant air is similar in magnitude to the amount of resistive losses.

23 January 2025 in Machines
Verified
Journal Article
Open access
PDF file
ARAvo Reinap
Avo Reinap
Samuel EstenlundSamuel Estenlund
Samuel Estenlund
CHConny Högmark
Conny Högmark
This article focuses on the analysis of a direct air-cooled rotor winding of a wound field synchronous machine, the innovation of which lies in the increase in the internal cooling surface, the cooling of the winding compared to the conventional inter-pole cooling, and the development of a CHT evaluation model accordingly. Conjugate heat transfer (CHT) analysis is used to explore the cooling efficacy of a parallel-cooled hollow-conductor winding of a salient-pole rotor and to identify a cooling performance map. The use of high current densities of 15–20 Arms/mm2 in directly cooled windings requires high cooling intensity, which in the case of air cooling results not only in flow velocities above 15 m/s to ensure permissible operating temperatures, but also the need for coolant distribution and heat transfer studies. The experiments and calculations are based on a non-rotating machine and a wind tunnel using the same rotor coil(s). CHT-based thermal calculations provide not only reliable results compared to experimental work and lumped parameter thermal circuits with adjusted aggregate parameters, but also insight related to pressure and cooling flow distribution, thermal loads, and cooling integration issues that are necessary for the development of high power density and reliable electrical machines. The results of the air-cooling integration show that the desired high current density is achievable at the expense of high cooling intensity, where the air velocity ranges from 15 to 30 m/s and 30 to 55 m/s, distinguishing the air velocity of the hollow conductor and bypass channel, compared to the same coil in an electric machine and a wind tunnel at the similar thermal load and limit. Since the hot spot location depends on cooling integration and cooling intensity, modeling and estimating the cooling flow is essential in the development of wound-field synchronous machines.

1 June 2020
Verified
Conference Paper
Closed access
Samuel EstenlundSamuel Estenlund
Samuel Estenlund
This paper presents theoretical and practical analyses of four different design options for an electrically excited synchronous machine (EESM) with hollow field winding conductors for internal air cooling. This cooling concept allows for effective direct cooling of the windings.Simulations are performed for the electromagnetic evaluation of the proposed designs, while a plastic 3D printed rotor mock- up is used to validate the winding method. The electromagnetic simulation results are used to estimate the increased losses during nominal excitation, for a comparison with a hypothetical corresponding PMSM. The rotor mock-up proved to be an effective way to test winding methods and rule out design options that worked well in theory, but not in practice.Based on the theoretical and practical analyses, a conclusion is drawn on what rotor design option is most suitable for this direct cooling concept. The chosen design has separate rotor teeth assembled to the rotor yoke with dovetails.

1 September 2024
Verified
Conference Paper
Closed access
Samuel EstenlundSamuel Estenlund
Samuel Estenlund
ARAvo Reinap
Avo Reinap
This paper presents the experimental verification of a cooling concept based on hollow direct air cooling windings for the rotor of an electrically excited synchronous machine (EESM) with the application of traction drive for electric vehicles (EVs). Developing the performance of EESMs is important for the EV industry since it is today so reliant on permanent magnets. The idea behind the cooling concept is explained and the prototype machine made for the experimental verification presented. The results of the experimental work show that the direct air cooled hollow windings can maintain a continuous current corresponding to a copper current density of 21.1 A/mm 2 or a rotor slot current density of 8.5 A/mm 2 .