Seokkan Ki

Prof. Seokkan Ki

Department of Mechatronics Engineering, Konkuk University Glocal Campus, Chungju, Chungbuk, Republic of Korea
orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 April 2024 in Advanced Science
Verified
Journal Article
Open access
Seokkan KiSeokkan Ki
Seokkan Ki
SSSeongjong Shin
Seongjong Shin
SCSumin Cho
Sumin Cho
SBSoosik Bang
Soosik Bang
DCDongwhi Choi
Dongwhi Choi
YNYoungsuk Nam
Youngsuk Nam
Gallium liquid metal is one of the promising phase change materials for passive thermal management of electronics due to their high thermal conductivity and latent heat per volume. However, it suffers from severe supercooling, in which molten gallium does not return to solid due to the lack of nucleation. It may require 28.2 °C lower temperature than the original freezing point to address supercooling, leading to unstable thermal regulation performance along fluctuations of cooling condition. Here, gallium is infused into porous copper in an oxide‐free environment, forming intermetallic compound impurities at the interfaces to reduce the activation energy for heterogeneous nucleation. The porous‐shaped gallium provides ≈63% smaller supercooling than that of the bulk type due to large specific surface area (≈9,070 cm 2 per cm 3 ) and high wetting characteristics (≈16° of contact angle) on CuGa 2 intermetallic layer. During repetitive heating‐cooling cycles, porous‐shaped gallium consistently shows propagation of crystallization at even near room temperature (≈25 °C) while maintaining stable performance as thermal buffer, whereas droplet‐shaped gallium is gradually degraded due to partial‐supercooled state. The findings will improve the responsive thermal regulation performance to relieve a rapid increase in temperature of semiconductors/batteries, and also have a potential for energy storage applications.

26 November 2023 in Applied Thermal Engineering
Verified
Journal Article
Closed access
SKSeungwoo Kim
Seungwoo Kim
Seokkan KiSeokkan Ki
Seokkan Ki
SBSoosik Bang
Soosik Bang
SHSanghyung Han
Sanghyung Han
JSJunyong Seo
Junyong Seo
YNYoungsuk Nam
Youngsuk Nam

1 March 2021 in International Journal of Thermal Sciences
Verified
Journal Article
Closed access
Seokkan KiSeokkan Ki
Seokkan Ki
JLJooyoung Lee
Jooyoung Lee
SRSeunggeol Ryu
Seunggeol Ryu
SBSoosik Bang
Soosik Bang
KKKichong Kim
Kichong Kim
YNYoungsuk Nam
Youngsuk Nam

22 September 2026 in Actuators
Verified
Journal Article
Open access
PDF file
Seokkan KiSeokkan Ki
Seokkan Ki
JLJun Yeong Lee
Jun Yeong Lee
JCJunggi Choi
Junggi Choi
GSGyu Hyeon Song
Gyu Hyeon Song
DHDuri Han
Duri Han
HSHyeonjun Sim
Hyeonjun Sim
Thermal comfort is a key determinant of human health and requires adaptive responses to dynamic environments. Here, we report a temperature-adaptive textile enabled by a tensile stress mismatch-driven poly(N-isopropylacrylamide) (PNIPAM) actuator operating within a human-friendly temperature range of 18–38 °C. A pre-stretched polyurethane core fiber integrated within a PNIPAM sheath in a noncoaxial configuration induces programmable bending through tensile-stress mismatch between elastic recovery and hydrogel swelling. Unlike conventional bilayer hydrogel actuators based on differential swelling between laminated layers, this pre-stretching strategy amplifies structural deformation through elastic restoring stress. When extended to a two-dimensional textile architecture, this strategy enables reversible, dynamic pore modulation with an approximately 400% increase in pore area. This study provides a promising platform for smart adaptive textiles, wearable healthcare, and soft robotics.

28 May 2024
Verified
Conference Paper
Closed access
Seokkan KiSeokkan Ki
Seokkan Ki
SSSeongjong Shin
Seongjong Shin
SCSumin Cho
Sumin Cho
SBSoosik Bang
Soosik Bang
HLHaejin Lee
Haejin Lee
YNYoungsuk Nam
Youngsuk Nam
Gallium (Ga)-based liquid metal (LM), belonging to metallic phase change materials (PCMs), stands out as an appealing candidate for a thermal buffer due to their high thermal conductivity (~40 W/mK in the solid state) and moderate latent heat (~80 J/g). Despite these advantages, LM-based PCMs encounter supercooling, which refers to the phenomenon where a molten material, having been pre-heated, fails to revert to the solid phase even when the temperature drops below the freezing point. If the supercooling is not addressed during the cooling, the thermal regulation performance may be insufficient. This is because only sensible heat is accessible, limiting the ability to effectively dissipate heat during the repetitive cycles. To effectively tackle the supercooling behavior, this study proposes a porous-shaped LM/PDMS composite. The aim is not only to decrease the free energy needed for heterogeneous nucleation between the LM and its substrate but also to establish a propagation path for rapid solidification, leveraging Cu backbone structure. In contrast to droplet-shaped LM/PDMS composites, our strategy has demonstrated a more sustainable thermal buffering effect, manifesting a propagation of crystallization even at near-room temperature. Thanks to both thermal percolation within the interconnected LM and the high wetting characteristics between the LM and the CuGa2 intermetallic layer, the porous-shaped LM/PDMS emerges as a viable candidate for passive thermal management strategies.

24 February 2023 in SSRN Electronic Journal
Verified
Preprint
Open access
PDF file
SBSoosik Bang
Soosik Bang
JKJeonghwan Kim
Jeonghwan Kim
SRSeunggeol Ryu
Seunggeol Ryu
Seokkan KiSeokkan Ki
Seokkan Ki
YHYun Jung Heo
Yun Jung Heo
YNYoungsuk Nam
Youngsuk Nam
We developed asymmetric capillary wicks composed of slanted microposts using inclined photolithography. Then we investigated the effects of inclination angle and wicking direction on the capillary and the heat transfer performances. The working fluid accelerates when it flows in the slope direction of the structure (forward direction, FD) and decelerates when it flows in the opposite slope direction (rear direction, RD). We applied the scaling law to the capillary rise experiment data to verify that the inclination angle and the wicking direction affect the capillary performance. The capillary performance parameter was improved by up to ~39% with FD case and decreased by 21.3% with RD. The heat transfer performance test showed that the wick-CHF (the enhanced critical heat flux due to the formation of the wick) of the asymmetric FD case was increased by 43.3% compared to symmetric ones while maintaining the heat transfer coefficient. This work shows that asymmetric evaporator wicks can enhance the critical heat flux without sacrificing the heat transfer coefficient, which can help develop high-performance thermal management solutions.