Serkan Guler

Dr. Serkan Guler

Iskenderun Technical University
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 May 2017 in Mechanical Systems and Signal Processing
Verified
Journal Article
Closed access
KMKemal Mazanoglu
Kemal Mazanoglu
SGSerkan Guler
Serkan Guler

1 February 2016 in Composites Part B: Engineering
Verified
Journal Article
Closed access
ASA. Seçgin
A. Seçgin
SGSerkan Guler
Serkan Guler
MKM. Kara
M. Kara

10 December 2021 in Mühendis ve Makina
Verified
Journal Article
Closed access
SGSerkan Guler
Serkan Guler
HSHüseyin Tarık SERİNDAĞ
Hüseyin Tarık SERİNDAĞ
Gurel ÇamGurel Çam
Gurel Çam
Yenilikçi bir imalat teknolojisi olan metal eklemeli imalat (MEİ) günümüzde havacılık-uzay, enerji, otomotiv, tıp gibi çeşitli endüstriyel alanlarda uygulanmaktadır. Bu imalat yöntemlerinde metal parçaların üretimi, üç farklı şekilde yapılmaktadır. Bunlar toz sermeli ergitme, toz beslemeli ergitme ve tel eklemeli ergitme sistemleridir. Bu yöntemlerden ilk ikisinde hammadde olarak metal veya alaşım tozları kullanılırken üçüncü yöntemde metal veya alaşımlardan imal edilmiş ilave tel başlangıç malzemesidir. Ancak, metal tozlarının özellikle de alaşım tozlarının maliyetleri oldukça yüksektir. Bu da tel kullanılarak yapılan eklemeli metal parça üretimini oldukça cazip hale getirmektedir. Tel ark eklemeli üretimin (TAEİ) diğer bir avantajı da, küçük ve orta büyüklükteki parçaların ekonomik olarak ve yüksek hızda üretebilmesi potansiyelidir. Günümüzde, bu yenilikçi imalat teknolojisi Ti ve alaşımları, Al ve alaşımları, Ni-esaslı alaşımlar ve çelik gibi değişik mühendislik malzemelerinden parça üretiminde ümit vadeden bir üretim teknolojisi olarak kabul edilmektedir. Bu makalede tel ark eklemeli imalat konusundaki çalışmalar ve yaygın kullanılan metalik teller tartışılacak ve bu yöntem ile üretilen parçaların içyapı ve mekanik özellikleri ele alınacaktır. Ayrıca, TAEİ’ta karşılaşılan deformasyon, porozite ve çatlak oluşumu gibi hatalar ve bunların nedenleri de tartışılacaktır. Son olarak bu üretim yönteminin metal parça imalatında yaygın olarak kullanılabilmesi için aşılması gereken sorunlar özetlenecektir. Metal additive manufacturing (MAM) which is an innovative technology is presently being applied in various industries such as aeronautics-space, energy, automotive, and medicine. Metal parts are produced in three different ways in metal additive manufacturing methods. These are powder bed fusion, powder fed fusion and wire fed fusion systems. In the first two of these methods, metal or alloy powders are used as raw materials, while in the third method, the filler wire made of metal or alloys is the starting material. However, metal powders, especially alloy powders, are quite costly. This in turn makes the production of metal parts using filler wire very attractive. Another advantage of wire arc additive manufacturing (WAAM) is its potential to produce small- and medium-sized parts economically with high deposition rate. Nowadays, this innovative manufacturing technology is being considered a promising fabrication technology for manufacturing several products from various engineering materials such as titanium and its alloys, aluminum and its alloys, nickel-based alloys and steels. In this paper, studies on WAAM and commonly used metallic wires and the microstructure and mechanical properties of the parts produced by this method will be discussed. In addition, defects such as deformation, porosity and crack formation encountered in WAAM and their reasons will also be discussed. Finally, the problems which have to be overcome for a wider application of this production method in the manufacturing of metallic parts, will be summarized.

13 July 2021 in Smart Materials and Structures
Verified
Journal Article
Closed access
MKM Kara
M Kara
SGSerkan Guler
Serkan Guler
ASA Seçgin
A Seçgin
Laminated composite plates are utilized due to their high strength/weight ratios. Since such structures are light and have less stiffness, their natural frequencies are lower than usual isotropic structures. Therefore, their behaviours in higher order modes are of interest. On the contrary, sensitivity analysis of vibrating structures is generally performed for lower order modes. In this study, sensitivity analysis of symmetrical/anti-symmetrical/asymmetrical laminated composite plates is performed in low to high order modes. In this regard, angular orientation, Young’s modulus, shear modulus, Poisson’s ratio and density of the plate are selected as design parameters whereas natural frequencies are selected as design objective functions. Discrete singular convolution method is used as solver due to its high computational capability. Although some other conclusions are drawn, it can mainly be concluded that, the natural frequencies are very sensitive to small differences in Poisson ratio for orientation angles of considered plates.

1 August 2016 in Latin American Journal of Solids and Structures
Verified
Journal Article
Open access
PDF file
SGSerkan Guler
Serkan Guler
HKHira Karagulle
Hira Karagulle
Extruded aluminum profiles are widely used in building and automation structures due to their durability, lightweight, corrosion resistance, shorter fastening time and reusability. Proper design is crucial in maintaining the lifespan of these structures. It is therefore essential to determine the structural behaviors of the structures such as the natural frequency, mode shape, etc. The finite element analysis is a method which has been commonly used in determining structural behaviors. However, there are also numerous problems in analyzing these kinds of profiles using solid finite elements, such as modeling, meshing, solution time problems, etc. Therefore, beam finite elements have been used in the present study in modeling of the profiles. Furthermore, an equivalent beam element model has been developed for bolt-together connectors of the profiles. Simulation and experimental modal analysis have been conducted on example test systems. It has been demonstrated that this modeling technique is very practical and the results obtained from the method agree well with the experimental results.