Quinary AlCoCrFeNi high entropy alloy (HEA) is one of the most studied alloys in the recent decade due to its outstanding properties. However, it is still far from becoming an applicable industrial alloy. To our understanding, in order to promote this, the role of elements, constituting the quinary alloy, needs to be defined. Knowing the role of each element, modification of the quinary alloy toward minimization of its disadvantages will be possible. In the current research, we shed some light on this subject, presenting a thorough investigation of the microstructure (carried out using scanning and transmission electron microscopy) and mechanical properties, performed by microhardness and fractography post small punch test (SPT), of five equiatomic quaternary alloys, constituting the quinary system, namely: CoCrFeNi, AlCoFeNi, AlCoCrNi, AlCoCrFe, and AlCrFeNi. CoCrFeNi (i.e., w/o Al) was found to be Face Centered Cubic (FCC) solid solution, exhibiting relatively low micro-hardness and ductile fracture post SPT measurement. AlCoFeNi (i.e., w/o Cr) was essentially single phase B2. Other alloys had a mixed BCC + B2 dual phase content with variable microstructures and sizes of particles. The fine microstructure of the alloy without Ni implies eutectic solidification or spinodal decomposition. This fine microstructure imposed remarkable high hardness though the alloy was too brittle and unmachinable. Among the BCC/B2 mixture alloys, Fe and Co-less ones resembled the most quinary AlCoCrFeNi in terms of microstructure and mechanical properties.
Prediction of the mechanical behavior of thin foils (~25 µm) requires special characterization techniques. The current work is focused on the mechanical and microstructural characterization of 25 µm HAVAR alloy foils following annealing, cold rolling, and subsequent heat treatments, using small punch testing (SPT), X-ray diffraction (XRD), and transmission-scanning electron microscopy (TEM). The SPT technique revealed that the annealed specimens exhibited the largest maximal load to failure and deformation (more than two-fold), compared to the cold rolled and heat treated conditions. The microscopy observations revealed high dislocation density following cold rolling and subsequent heat treatments. Following annealing, a cubic crystallographic structure (FCC) with equiaxed grains and a limited dislocation population was observed. Following cold rolling and subsequent thermal treatment, a preferred orientation texture (i.e., ‘deformation texture’) was observed with a very high dislocation density. The correlation between the mechanical behavior and the microstructural observations is discussed in detail.
PH13-8Mo is a precipitation hardened martensitic stainless steel, known for its high strength but also for its high sensitivity to hydrogen embrittlement. Small punch test, SPT (also referred to as the ball punch test, BPT), is a relatively simple and new technique to assess the mechanical properties of samples under biaxial loading conditions. The current study utilizes the unique loading conditions of SPT to investigate the mechanical behavior and fracture prior to and after the hydrogen charging of PH13-8Mo steel. The mechanical characteristics were investigated at different metallurgical conditions: solution and quenched (SQ); fully-aged (550 °C for 4 h) and over-aged (600 °C for 4 h). Samples were cathodically hydrogen charged in a 1 M H2SO4 solution containing NaAsO2 (0.125 mg/L) at 50 mA/cm2 for different durations of 0.5 h, 2 h, and 19 h, and compared to the as-heat-treated condition. A fractographic examination was performed following the SPT measurements by scanning electron microscopy (SEM). Transmission electron microscopy (TEM) and x-ray diffraction (XRD) analyses were used as complementary characterization tools. It is shown that upon hydrogen charging, the SPT fracture mode changes from ductile to completely brittle with a transition of mixed mode cracking also affecting the SPT load-displacement curve.
The effects of the secondary processes of Hot Isostatic Pressing (HIP) at 920 °C and Heat Treatment (HT) at 1000 °C of Electron Beam-Melted (EBM) Ti–6Al–4V alloy on the microstructure and hydrogen embrittlement (HE) after electrochemical hydrogen charging (EC) were investigated. Comprehensive characterization, including microstructural analysis, X-ray diffraction (XRD), thermal desorption analysis, and mechanical testing, was conducted. After HIP, the β-phase morphology changed from discontinuous Widmanstätten to a more continuous structure, 10 times and ~1.5 times larger in length and width, respectively. Following HT, the β-phase morphology changed to a continuous “web-like” structure, ~4.5 times larger in width. Despite similar mechanical behavior in their non-hydrogenated state, the post-treated alloys exhibit increased susceptibility to HE due to enhanced hydrogen penetration into the bulk. It is shown that hydrogen content in the samples’ bulk is inversely dependent on surface hydride content. It is therefore concluded that the formed hydride surface layer is crucial for inhibiting further hydrogen penetration and adsorption into the bulk and thus for reducing HE susceptibility. The lack of a hydride surface layer in the samples subject to HIP and HT highlights the importance of choosing secondary treatment process parameters that will not increase the continuous β-phase morphology of EBM Ti–6Al–4V alloys in applications that involve electrochemical hydrogen environments.