Sensors are ubiquitous in modern society because of their wide applications in healthcare, security, forensic industries as well as environmental protection. Specifically, sensors which can be microfabricated employing very-large-scale-integration (VLSI) compatible microfabrication techniques are particularly desirable. This is because they can provide several advantages: small size, low cost, and possibility of mass fabrication. 2D materials are a promising building block for such sensors. Their atomically thin nature, flat surfaces and ability to form van der Waals hetero junctions opens up the pathway for versatile functionalities. Here, we review 2D material-based field-effect-transistors (FETs) and nano-electro-mechanical systems (NEMs) for applications in detecting different gases, chemicals, and biomolecules. We will provide insights into the unique advantages of these materials for these sensing applications and discuss the fabrication methods, detection schemes and performance pertaining to these technologies. Finally, we will discuss the current challenges and prospects for this field.
29 December 2015 in Journal of Materials Science: Materials in Electronics
Bioelectronic implants for brain stimulation are used to treat brain disorders but require invasive surgery. To provide a noninvasive alternative, we report nonsurgical implants consisting of immune cell–electronics hybrids, an approach we call Circulatronics. The devices can be delivered intravenously and traffic autonomously to regions of inflammation in the brain, where they implant and enable neuromodulation, circumventing the need for surgery. To achieve suitable electronics, we designed and built subcellular-sized, wireless, photovoltaic electronic devices that harvest optical energy with high power conversion efficiency. In mice, we demonstrate nonsurgical implantation in an inflamed brain region, as an example of therapeutic target for several neural diseases, by employing monocytes as cells, covalently attaching them to the subcellular-sized, wireless, photovoltaic electronic devices and administering the resulting hybrids intravenously. We also demonstrate neural stimulation with 30-µm precision around the inflamed region. Thus, by fusing electronic functionality with the biological transport and targeting capabilities of living cells, this technology can form the foundation for autonomously implanting bioelectronics.
5 August 2025 in IEEE Transactions on Antennas and Propagation
Wireless battery-free implants can harvest power from externally applied waves, yet powering deep-tissue implants remains complex. Although optical waves undergo absorption in dense tissue structures and acoustic waves encounter interference from impedance mismatch, kHz RF waves achieve superior tissue penetration. However, miniaturizing RF antennas is challenging. Our study introduces a solution via an ultra-miniaturized magnetoelectric antenna, 200 μm in diameter, operating at the low frequency (LF) band. This antenna relies on the magnetoelectric effect, converting incident magnetic waves into electric charges through a mechanical coupling between magnetostrictive and piezoelectric thin films of 250 nm in thickness. Our device has a magnetoelectric coupling coefficient of 768 V ∙ cm-1Oe-1 at 109.3 kHz, showcasing its efficacy even in regions deep inside the body. Moreover, our device fabrication is VLSI-compatible, promising potential integration with CMOS circuitry and positioning it as a prospective frontrunner for minimally invasive bioelectric applications.
Higher efficiency ternary organic solar cells (OSCs) can be built by capping the photoactive layer of a binary blend OSC device with a planar single photovoltaic layer, with an absorption spectrum complementary to that for the original blend layer. A ternary active layer material system of two donors poly (3-hexylthiophene) and Poly[2,6-(4,4-bis-(2-ethylhexyl)-4 H -cyclopenta [2,1- b ;3,4- b ′] dithiophene)- alt -4,7(2,1,3-benzothiadiazole)] and an acceptor [6,6]-Phenyl C 61 butyric acid methyl ester is considered in this work. From the various possibilities of building ternary device with a binary blend layer and planar single layer stacks, the low efficiency options are eliminated. Simulation studies of the final structure are carried out to decide the optimum thicknesses of the different photovoltaic layers. The optimised ternary device fabricated shows an improvement in power conversion efficiency of up to 23.5% over the base binary blend solar cells. The primary contribution to efficiency improvement is from the increase in short circuit current from the increased harvest of photons by the planar single capping layer.