Ahmad Noor Syimir Fizal

Dr. Ahmad Noor Syimir Fizal

Universiti Kuala Lumpur- Malaysian Institute of Chemical and Bioengineering Technology (UniKL MICET), Melaka, Malaysia
+1
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 March 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
RGRianyza Gayatri
Rianyza Gayatri
AFAhmad Noor Syimir Fizal
Ahmad Noor Syimir Fizal
EYErna Yuliwati
Erna Yuliwati
MHMd. Sohrab Hossain
Md. Sohrab Hossain
Juhana JaafarJuhana Jaafar
Juhana Jaafar
AYAhmad Naim Ahmad Yahaya
Ahmad Naim Ahmad Yahaya
Polymeric membranes offer straightforward modification methods that make industry scaling affordable and easy; however, these materials are hydrophobic, prone to fouling, and vulnerable to extreme operating conditions. Various attempts were made in this study to fix the challenges in using polymeric membranes and create mixed-matrix membrane (MMMs) with improved properties and hydrophilicity by adding titanium dioxide (TiO2) and pore-forming agents to hydrophobic polyvinylidene fluoride (PVDF). The PVDF mixed-matrix ultrafiltration membranes in this study were made using the non-solvent phase inversion approach which is a simple and effective method for increasing the hydrophilic nature of membranes. Polyvinylpyrrolidone (PVP) and polyethylene glycol (PEG) as pore-forming chemicals were created. Pure water flux, BSA flux, and BSA rejection were calculated to evaluate the mixed-matrix membrane’s efficiency. Bovine serum albumin (BSA) solution was employed in this study to examine the protein rejection ability. Increases in hydrophilicity, viscosity, and flux in pure water and BSA solution were achieved using PVP and PEG additives. The PVDF membrane’s hydrophilicity was raised with the addition of TiO2, showing an increased contact angle to 71°. The results show that the PVDF–PVP–TiO2 membrane achieved its optimum water flux of 97 L/(m2h) while the PVDF–PEG–TiO2 membrane rejected BSA at a rate greater than 97%. The findings demonstrate that use of a support or additive improved filtration performance compared to a pristine polymeric membrane by increasing its hydrophilicity.

29 November 2023 in Polymers
Verified
Journal Article
Open access
PDF file
MBMohd Faizar Banjar
Mohd Faizar Banjar
Fatin Najwa Joynal AbedinFatin Najwa Joynal Abedin
Fatin Najwa Joynal Abedin
AFAhmad Noor Syimir Fizal
Ahmad Noor Syimir Fizal
NSNorazilawati Muhamad Sarih
Norazilawati Muhamad Sarih
MHMd. Sohrab Hossain
Md. Sohrab Hossain
Muzafar ZulkifliMuzafar Zulkifli
Muzafar Zulkifli
Polyaniline (PANI) is a conductive polymer easily converted into a conducting state. However, its limited mechanical properties have generated interest in fabricating PANI composites with other polymeric materials. In this study, a PANI–prevulcanized latex composite film was synthesized and fabricated in two phases following chronological steps. The first phase determined the following optimum parameters for synthesizing nanosized PANI, which were as follows: an initial molar ratio of 1, a stirring speed of 600 rpm, a synthesis temperature of 25 °C, purification via filtration, and washing using dopant acid, acetone, and distilled water. The use of a nonionic surfactant, Triton X-100, at 0.1% concentration favored PANI formation in a smaller particle size of approximately 600 nm and good dispersibility over seven days of observation compared to the use of anionic sodium dodecyl sulfate. Ultraviolet–visible spectroscopy (UV-Vis) showed that the PANI synthesized using a surfactant was in the emeraldine base form, as the washing process tends to decrease the doping level in the PANI backbone. Our scanning electron microscopy analysis showed that the optimized synthesis parameters produced colloidal PANI with an average particle size of 695 nm. This higher aspect ratio explained the higher conductivity of nanosized PANI compared to micron-sized PANI. Following the chronological steps to determine the optimal parameters produced a nanosized PANI powder. The nanosized PANI had higher conductivity than the micron-sized PANI because of its higher aspect ratio. When PANI is synthesized in smaller particle sizes, it has higher conductivity. Atomic force microscopy analysis showed that the current flow is higher across a 5 µm2 scanned area of nanosized PANI because it has a larger surface area. Thus, more sites for the current to flow through were present on the nanosized PANI particles.

29 May 2023 in Polymers
Verified
Journal Article
Open access
PDF file
ARAida Syafiqah Abdul Rahman
Aida Syafiqah Abdul Rahman
AFAhmad Noor Syimir Fizal
Ahmad Noor Syimir Fizal
Nor Afifah KhalilNor Afifah Khalil
Nor Afifah Khalil
AYAhmad Naim Ahmad Yahaya
Ahmad Naim Ahmad Yahaya
MHMd. Sohrab Hossain
Md. Sohrab Hossain
Muzafar ZulkifliMuzafar Zulkifli
Muzafar Zulkifli
The implementation of inorganic adsorbents for the removal of heavy metals from industrial effluents generates secondary waste. Therefore, scientists and environmentalists are looking for environmentally friendly adsorbents isolated from biobased materials for the efficient removal of heavy metals from industrial effluents. This study aimed to fabricate and characterize an environmentally friendly composite bio-sorbent as an initiative toward greener environmental remediation technology. The properties of cellulose, chitosan, magnetite, and alginate were exploited to fabricate a composite hydrogel bead. The cross linking and encapsulation of cellulose, chitosan, alginate, and magnetite in hydrogel beads were successfully conducted through a facile method without any chemicals used during the synthesis. Energy-dispersive X-ray analysis verified the presence of element signals of N, Ca, and Fe on the surface of the composite bio-sorbents. The appearance and peak’s shifting at 3330–3060 cm−1 in the Fourier transform infrared spectroscopy analysis of the composite cellulose–magnetite–alginate, chitosan–magnetite–alginate, and cellulose–chitosan–magnetite–alginate suggested that there are overlaps of O-H and N-H and weak interaction of hydrogen bonding with the Fe3O4 particles. Material degradation, % mass loss, and thermal stability of the material and synthesized composite hydrogel beads were determined through thermogravimetric analysis. The onset temperature of the composite cellulose–magnetite–alginate, chitosan–magnetite–alginate, and cellulose–chitosan–magnetite–alginate hydrogel beads were observed to be lower compared to raw-material cellulose and chitosan, which could be due to the formation of weak hydrogen bonding resulting from the addition of magnetite Fe3O4. The higher mass residual of cellulose–magnetite–alginate (33.46%), chitosan–magnetite–alginate (37.09%), and cellulose–chitosan–magnetite–alginate (34.40%) compared to cellulose (10.94%) and chitosan (30.82%) after degradation at a temperature of 700 °C shows that the synthesized composite hydrogel beads possess better thermal stability, owing to the addition of magnetite and the encapsulation in the alginate hydrogel beads.

7 June 2021 in International Journal of Green Energy
Verified
Journal Article
Closed access
AFAhmad Noor Syimir Fizal
Ahmad Noor Syimir Fizal
MHMd. Sohrab Hossain
Md. Sohrab Hossain
Muzafar ZulkifliMuzafar Zulkifli
Muzafar Zulkifli
Nor Afifah KhalilNor Afifah Khalil
Nor Afifah Khalil
HHHamidah Abd Hamid
Hamidah Abd Hamid
AYAhmad Naim Ahmad Yahaya
Ahmad Naim Ahmad Yahaya
The demand for renewable energy has risen rapidly due to the depletion of petroleum oil. Biodiesel has attracted potential interest to be utilized as an alternative to petroleum oil since it is produced from renewable resources with minimal environmental impact. However, the production and quality of biodiesel potentially influence several factors including physicochemical properties of lipids, selection of feedstock, and technology utilized for lipids extraction. Candlenut contains the highest amount of oil among the oilseed crops. Supercritical carbon dioxide (scCO2) is viewed as an effective alternative method over conventional solvent extraction methods for the extraction and separation of lipids from various plant matrices. The distinct properties of the fluid CO2, such as nonflammability, nontoxicity, environmental friendliness, and its ability to solubilize lipophilic substance led to the wide application of the scCO2 in various industrial applications. Hence, the present study attempts to review the influence of the supercritical carbon dioxide (scCO2) technology for the extraction of lipids from candlenut as a potential feedstock for biodiesel production. The limitations of existing technologies in candlenut oil extraction and the potential scCO2 technology for the extraction of lipids from candlenut were also reviewed.

29 September 2021 in Polymers
Verified
Journal Article
Open access
PDF file
Muhammad Nasrullah Mat RoziMuhammad Nasrullah Mat Rozi
Muhammad Nasrullah Mat Rozi
HHHamidah Abd Hamid
Hamidah Abd Hamid
MHMd. Sohrab Hossain
Md. Sohrab Hossain
Nor Afifah KhalilNor Afifah Khalil
Nor Afifah Khalil
AYAhmad Naim Ahmad Yahaya
Ahmad Naim Ahmad Yahaya
Muzafar ZulkifliMuzafar Zulkifli
Muzafar Zulkifli
A multi-objective optimization of in situ sol-gel process was conducted in preparing oil palm fiber-reinforced polypropylene (OPF-PP) composite for an enhancement of mechanical and thermal properties. Tetraethyl orthosilicate (TEOS) and butylamine were used as precursors and catalysts for the sol-gel process. The face-centered central composite design (FCCD) experiments coupled with response surface methodology (RSM) has been utilized to optimize in situ silica sol-gel process. The optimization process showed that the drying time after the in-situ silica sol-gel process was the most influential factor on silica content, while the molar ratio of TEOS to water gave the most significant effect on silica residue. The maximum silica content of 34.1% and the silica residue of 35.9% were achieved under optimum conditions of 21.3 h soaking time, 50 min drying time, pH value of 9.26, and 1:4 molar ratio of TEOS to water. The untreated oil palm fiber (OPF) and silica sol-gel modified OPF (SiO2-OPF) were used as the reinforcing fibers, with PP as a matrix and maleic anhydride grafted polypropylene (MAgPP) as a compatibilizer for the fiber-reinforced PP matrix (SiO2-OPF-PP-MAgPP) composites preparation. The mechanical and thermal properties of OPF-PP, SiO2-OPF-PP, SiO2-OPF-PP-MAgPP composites, and pure PP were determined. It was found that the OPF-S-PP-MAgPP composite had the highest toughness and stiffness with values of tensile strength, Young’s modulus, and elongation at break of 30.9 MPa, 881.8 MPa, and 15.1%, respectively. The thermal properties analyses revealed that the OPF-S-PP-MAgPP exhibited the highest thermally stable inflection point at 477 °C as compared to pure PP and other composites formulations. The finding of the present study showed that the SiO2-OPF had the potential to use as a reinforcing agent to enhance the thermal-mechanical properties of the composites.

18 December 2022 in Materials Today: Proceedings
Verified
Journal Article
Closed access
NKNor Afifah Khalil
Nor Afifah Khalil
ARAida Syafiqah Abdul Rahman
Aida Syafiqah Abdul Rahman
AHAlnazirul Mubin Abu Huraira
Alnazirul Mubin Abu Huraira
SJSiti Nur Dalillah Fattin Janurin
Siti Nur Dalillah Fattin Janurin
AFAhmad Noor Syimir Fizal
Ahmad Noor Syimir Fizal
AYAhmad Naim Ahmad Yahaya
Ahmad Naim Ahmad Yahaya