Polymeric membranes offer straightforward modification methods that make industry scaling affordable and easy; however, these materials are hydrophobic, prone to fouling, and vulnerable to extreme operating conditions. Various attempts were made in this study to fix the challenges in using polymeric membranes and create mixed-matrix membrane (MMMs) with improved properties and hydrophilicity by adding titanium dioxide (TiO2) and pore-forming agents to hydrophobic polyvinylidene fluoride (PVDF). The PVDF mixed-matrix ultrafiltration membranes in this study were made using the non-solvent phase inversion approach which is a simple and effective method for increasing the hydrophilic nature of membranes. Polyvinylpyrrolidone (PVP) and polyethylene glycol (PEG) as pore-forming chemicals were created. Pure water flux, BSA flux, and BSA rejection were calculated to evaluate the mixed-matrix membrane’s efficiency. Bovine serum albumin (BSA) solution was employed in this study to examine the protein rejection ability. Increases in hydrophilicity, viscosity, and flux in pure water and BSA solution were achieved using PVP and PEG additives. The PVDF membrane’s hydrophilicity was raised with the addition of TiO2, showing an increased contact angle to 71°. The results show that the PVDF–PVP–TiO2 membrane achieved its optimum water flux of 97 L/(m2h) while the PVDF–PEG–TiO2 membrane rejected BSA at a rate greater than 97%. The findings demonstrate that use of a support or additive improved filtration performance compared to a pristine polymeric membrane by increasing its hydrophilicity.
9 January 2024 in Case Studies in Chemical and Environmental Engineering
The increasing growth of the textile industry does not only provide benefits in the economic sector but also has the potential to damage the environment, because it generates the dye wastewater which is hard to eliminate. Procion red is one of the synthetic textile dyes that is toxic to the...
1 August 2022 in Journal of Ecological Engineering
Laboratory wastewater contains organic and inorganic compounds that are harmful to the environment when dispose without prior treatment. Beside of the high COD and BOD values, the laboratory wastewater also contains metals such as iron (Fe), zinc (Zn), copper (Cu), chromium (Cr), and lead (Pb)...
21 July 2020 in International Journal of Technology
The development of textile factories has had a significant impact on the environment because dye wastewater is difficult to degrade. The handling of textile wastewater usually involves the adsorption method, in which pollutants only transfer to another phase. As an alternative solution, a photodegradation method was developed using photocatalyst material assisted by ultraviolet irradiation. In this photodegradation method, dye substances are broken down into components that are simpler and safer for the environment. The possibility of using sunlight as a radiation source makes this a particularly promising method for countries such as Indonesia. Procion red, one of the most commonly utilized synthetic dyes in the home textile or Batik industry, was used as a model pollutant in this study. The objectives of the present research were to synthesize and characterize a nano-photocatalyst of ZnO-natural zeolite with the capacity to degrade Procion red. This nano-photocatalyst was synthesized using the sol-gel method, by which Zn(CH3COO)2 2H2O was used as a precursor and combined with natural zeolite to increase its photocatalytic ability. The nano-photocatalyst was characterized using X-ray diffraction (XRD), scanning electron microscope/energy dispersive X-ray spectroscopy (SEM/EDX), and Brunauer-Emmett-Teller (BET). The activity of nano-photocatalyst ZnO-natural zeolite was compared to ZnO alone and natural zeolite alone in terms of its ability to degrade Procion red. An average photocatalyst crystallite diameter of 82 nm was achieved, proving that a nano-sized photocatalyst of ZnO-natural zeolite was successfully synthesized. BET characterization showed that nano-photocatalyst ZnO-natural zeolite had a specific surface area of 14.84 m2/g, a pore size of 32.71 nm, and a pore volume of 0.12 cm2/g. A peak Procion red degradation percentage of 96.23% was obtained using nano-photocatalyst ZnO-natural zeolite after 120 minutes of irradiation under sunlight applied to a Procion red concentration of 50 ppm.