Agnes Nagyne Szokol

Mrs. Agnes Nagyne Szokol

Wigner Research Centre for Physics, Budapest, Hungary
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
Attila BonyárAttila Bonyár
Attila Bonyár
MSMelinda Szalóki
Melinda Szalóki
ABAlexandra Borók
Alexandra Borók
IRIstván Rigó
István Rigó
JKJudit Kámán
Judit Kámán
NCNAPLIFE Collaboration
NAPLIFE Collaboration
In this work, the effects of femtosecond laser irradiation and doping with plasmonic gold nanorods on the degree of conversion (DC) of a urethane dimethacrylate (UDMA)–triethylene glycol dimethacrylate (TEGDMA) nanocomposite were investigated. The UDMA-TEGDMA photopolymer was prepared in a 3:1 weight ratio and doped with dodecanethiol- (DDT) capped gold nanorods of 25 × 75 or 25 × 85 nm nominal diameter and length. It was found that the presence of the gold nanorods alone (without direct plasmonic excitation) can increase the DC of the photopolymer by 6–15%. This increase was found to be similar to what could be achieved with a control heat treatment of 30 min at 180 °C. It was also shown that femtosecond laser impulses (795 nm, 5 mJ pulse energy, 50 fs pulse length, 2.83 Jcm−2 fluence), applied after the photopolymerization under a standard dental curing lamp, can cause a 2–7% increase in the DC of undoped samples, even after thermal pre-treatment. The best DC values (12–15% increase) were obtained with combined nanorod doping and subsequent laser irradiation close to the plasmon resonance peak of the nanorods (760–800 nm), which proves that the excited plasmon field can directly facilitate double bond breakage (without thermoplasmonic effects due to the short pulse length) and increase the crosslink density independently from the initial photopolymerization process.

17 May 2023 in Universe
Verified
Journal Article
Open access
PDF file
TBTamás Sándor Biró
Tamás Sándor Biró
NKNorbert Kroo
Norbert Kroo
LCLaszlo Csermai
Laszlo Csermai
MVMiklos Veres
Miklos Veres
MAMárk Aladi
Márk Aladi
MSMelinda Szalóki
Melinda Szalóki
A status report is presented about the Nanoplasmonic Laser Induced Fusion Experiment (NAPLIFE). The goal is to investigate and verify plasmonically enhanced phenomena on the surfaces of nanoantennas embedded in a polymer target at laser intensities up to a few times 1016 W/cm2 and pulse durations of 40–120 fs. The first results on enhanced crater formation for Au-doped polymer targets are shown, and SERS signals typical for CD2 and ND bound vibrations are cited. Trials to detect D/H ratio by means of LIBS measurments are reported. Plasmonics has the potential to work at these intensities, enhancing the energy and deuterium production, due to thus far unknown mechanisms.

3 April 2025 in The European Physical Journal Special Topics
Verified
Journal Article
Open access
PDF file
ASAgnes Nagyne Szokol
Agnes Nagyne Szokol
JKJudit Kámán
Judit Kámán
RHRoman Holomb
Roman Holomb
IRIstván Rigó
István Rigó
MAMárk Aladi
Márk Aladi
NCNAPLIFE Collaboration
NAPLIFE Collaboration
The effect of embedded plasmonic gold nanoparticles on the crater morphology was studied in 160 µm-thick UDMA–TEGDMA copolymer films irradiated by femtosecond single pulses of a Ti:Sa laser. The plasmonic absorption of the embedded gold nanorods had a resonance at the wavelength of the laser. It was observed that by increasing the laser intensity the diameter of the craters decreased, while the depth of the craters increased. In addition, the crater depths were significantly higher in the presence of gold nanorods. A threshold intensity of 1.5·1017 W/cm2 has been determined, above which a doubled roughness and sevenfold increased crater volume was observed in the polymer containing gold nanorods. Graphical abstract

29 January 2025 in Sensors
Verified
Journal Article
Open access
PDF file
IBIstván Bányász
István Bányász
GNGyula Nagy
Gyula Nagy
VHVladimír Havranek
Vladimír Havranek
MBMaria Cinta Pujol Baiges
Maria Cinta Pujol Baiges
ASAgnes Nagyne Szokol
Agnes Nagyne Szokol
Istvan RajtaIstvan Rajta
Istvan Rajta
High diffraction efficiency optical transmission gratings with quasi-sinusoidal and saw-tooth surface relief profiles were fabricated in Bi12GeO20, Er: LiNbO3 and Er: Fe: LiNbO3 crystals by ion beam implantation. The gratings were directly written by nitrogen ion microbeams at energies of 5 MeV and 10.5 MeV. The finest grating constant was 4 μm. Grating constants for the majority of the gratings were 16 μm. The highest amplitudes of the gratings reached 1600 nm. The highest first-order diffraction efficiency obtained in a sinusoidal grating was 25%, close to the theoretical maximum of 33%. The highest first-order diffraction efficiency of a blazed grating was also 25%, without Littrow optimization. Such gratings can be incorporated into integrated optical biosensors.

5 August 2026 in Sensors
Verified
Journal Article
Open access
PDF file
IBIstván Bányász
István Bányász
GNGyula Nagy
Gyula Nagy
Istvan RajtaIstvan Rajta
Istvan Rajta
VHVladimír Havranek
Vladimír Havranek
ALAndrás József Laki
András József Laki
RMRobert Magnusson
Robert Magnusson
Direct writing of microstructures in ZEONOR™ cyclic olefin polymer, using a high-energy medium-mass ion microbeam, was proposed and demonstrated. Microbeams of 10.5 MeV N4+ ions were used. The implanted fluences were between 2.5·1012 and 2.0·1013 ion/cm2. The microstructures were surface relief optical gratings of quasi-sinusoidal profile and grating constant of 4, 8 and 16 µm. Peak-to-peak amplitudes of the gratings ranged from 10 to 90 nm. Measured profiles of the gratings were Fourier-analyzed. Highest measured net first-order diffraction efficiencies were between 25 and 29% at wavelengths of 405 and 640 nm, very close to the theoretical maximum of 33%, calculated with the Raman-Nath equation. This method could be used for the production of micro- and nanostructures in cyclic olefin polymers and copolymers and other polymers as well, either for the direct production of label-free biosensors and other devices, or to produce masters for hot stamping of such structures.