Titus Nghipulile

Dr. Titus Nghipulile

Civil, Mining and Process Engineering, Namibia University of Science and Technology, Windhoek, Khomas, Namibia
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 October 2023 in Minerals
Verified
Journal Article
Open access
PDF file
Titus NghipulileTitus Nghipulile
Titus Nghipulile
Sandile NkwanyanaSandile Nkwanyana
Sandile Nkwanyana
NLNiyoshaka Lameck
Niyoshaka Lameck
Comparative high pressure grinding rolls (HPGR) and cone crusher pilot-scale tests were conducted using Upper Group 2 (UG2) platinum-bearing ore in order to determine the impact of micro-cracks in HPGR products toward energy requirements in ball mills and the degree of liberation. The ball mill was fed with HPGR and cone crusher products of similar particle size distributions (PSDs). Qualitative analysis of the degree of micro-cracking on the HPGR and cone crusher products performed using scanning electron microscope (SEM) and image analysis software showed that an HPGR product had more micro-cracks than the equivalent cone crusher product. Milling energy requirements were evaluated using size-specific energy consumption indices calculated based on three grind sizes of 300 µm, 150 µm and 75 µm. The effect of residual micro-cracks in the products of HPGR and cone crusher on the milling size-specific energy requirement is inconclusive. The kinetic parameter k in the cumulative rate kinetic model for ball milling cone crusher products and for ball milling HPGR products were similar. Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) was used to determine the degree of liberation of various mineral phases in the mill products. At a coarser grind size (P80 of 300 µm), the sulfides in the mill products pre-crushed using the cone crusher have consistently poorer liberation than in the equivalent HPGR pre-crushed sample. However, at a finer grind size (P80 of 75 µm), the sulfides in the mill products pre-crushed using the cone crusher and using an HPGR showed similar liberation.

8 September 2023 in Materials
Verified
Journal Article
Open access
PDF file
GDGodfrey Dzinomwa
Godfrey Dzinomwa
BMBenjamin Mapani
Benjamin Mapani
Titus NghipulileTitus Nghipulile
Titus Nghipulile
KMKasonde Maweja
Kasonde Maweja
JKJaquiline Tatenda Kurasha
Jaquiline Tatenda Kurasha
KCKayini Chigayo
Kayini Chigayo
The depletion of the ore reserves in the world necessitates the search for secondary sources such as waste products (tailings and slag). The treatment and cleaning up of such secondary sources also has a positive impact on the environment. A smelter in Namibia we examined had historic slag which accumulated over decades of its operating life, thus posing the challenge of how best to collect representative samples to evaluate and propose viable methods of recovering contained metals. In this study, analytical and mineralogical characterization of the slag was performed using X-ray fluorescence (XRF) analysis, atomic absorption spectrometer (AAS), ICP-OES, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS) analysis, and optical microscopy analysis. The chemical analyses showed that the metal values contained in the slag were mainly copper, lead, and zinc whose average contents were approximately 0.35% Cu, 3% Pb, and 5.5% Zn. About 10.5% Fe was also contained in the slag. Germanium was detected by scanning electron microscopy, but was however below detection limits of the chemical analysis equipment used. Based on the results, approximate conditions under which the different slag phases were formed were estimated and the recovery routes for the various metals were proposed. Analysis by both optical and scanning electron microscopy revealed that Zn and Fe occurred mainly in association with O as oxides, while Cu and Pb were mainly associated with S as sulphides. The slag consisted of three different phases, namely the silicate phase (slag), metallic phase and the sulphide phases. The phases in the slag were mainly silicate phases as well as metallic and sulphide phases. It was observed that the metallic and sulphide phases were dominant in the finer size fractions (−75 µm) whereas the sulphide phase was also present in the coarser size fractions (+300 µm). An important finding from the microscopy examination was that the sulphide phases were interstitial and could be liberated from the slag. This finding meant that liberation and subsequent concentration of the sulphide phases was feasible using conventional processing techniques.

20 June 2024 in Minerals
Verified
Journal Article
Open access
PDF file
Titus NghipulileTitus Nghipulile
Titus Nghipulile
MBMurray Bwalya
Murray Bwalya
IGIndresan Govender
Indresan Govender
HShenry simonsen
henry simonsen
Innovation in comminution is expected to continue unabated to address the inefficiencies that are inherent in comminution circuits. The rotary offset crusher (ROC) is a new comminution device with a promising performance potential in terms of throughput due to the enhanced speed of transportation induced by the centrifugal force of the discs. However, the processes driving the comminution of particles trapped in the conical space between the two discs of the crusher are not fully understood. To gain a better insight into the comminution process in this device, discrete element modeling (DEM) simulations were conducted to study the breakage of a single particle for the crusher operated under two different dynamic conditions, i.e., (1) a stationary top disc and (2) both discs rotating at the same speed. For both scenarios, the speed of the discs was varied between 550 and 2350 rpm. Experimental testwork was also conducted with the laboratory prototype to generate the data that were used to calibrate the breakage parameters of the Ab × t10 breakage model. Simulations were performed using polyhedral UG2 ore particles that were generated with the in-built particle generator in the DEM simulator. The simulated ROC, which is operated with both discs rotating, outperformed the ROC with a stationary top disc in terms of the specific input energy and throughput. The crusher with a stationary top disc is characterized by high shear forces (suggesting a higher wear rate), specific input energies greater than 1 kWh/t, and low throughputs (<50 kg/h). The ROC operated with a stationary disc is not recommended for hard rock applications due to expected excessive wear of crushing surfaces and higher energy consumption. The freewheeling discs are recommended, but there is scope to optimize the crusher performance in terms of the power draw, size reduction, and throughput by manipulating the difference between the speeds of the discs. There is also scope to optimize the crusher performance when it is simulated with many particles. Once the full performance potential of the ROC is established, it will then be important to benchmark it against the existing crushers in the minerals industry as well as other industries where crushers are used.

14 April 2023 in Journal of the Southern African Institute of Mining and Metallurgy
Verified
Journal Article
Open access
PDF file
Titus NghipulileTitus Nghipulile
Titus Nghipulile
TMThomas Ehongo Moongo
Thomas Ehongo Moongo
GDG. Dzinomwa
G. Dzinomwa
KMK. Maweja
K. Maweja
BMB. Mapani
B. Mapani
MAMartha Amwaama
Martha Amwaama
The effect of mineralogy on the grindability was investigated using three copper ores - two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was bornite-rich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

31 July 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
GDGodfrey Dzinomwa
Godfrey Dzinomwa
BMBenjamin Mapani
Benjamin Mapani
Titus NghipulileTitus Nghipulile
Titus Nghipulile
KMKasonde Maweja
Kasonde Maweja
JKJaquiline Tatenda Kurasha
Jaquiline Tatenda Kurasha
KCKayini Chigayo
Kayini Chigayo
The depletion of the ore reserves in the world necessitates the search for secondary sources such as waste products (tailings and slag). A smelter in Namibia has historic slag which accumulated over decades of its operating life. Analytical and mineralogical characterization of the slag was performed using the X-ray fluorescence (XRF) analysis, Atomic Absorption Spectrometer (AAS), ICP-OES, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS) analysis, and optical microscopy analysis. The chemical analyses showed that the metal values contained in the slag were mainly copper, lead, and zinc whose average contents were approximately 0.3%Cu, 2.4%Pb and 3.2%Zn. About 10.5%Fe was also contained in the slag. Germanium was detected by scanning electron microscopy, but was however below detection limits of the chemical analysis equipment used. Based on the results, approximate conditions under which the different slag phases were formed were estimated and the recovery routes for the various metals were proposed. Analysis by both optical and scanning electron microscopy revealed that Zn and Fe occurred mainly in association with O as oxides, while Cu and Pb were mainly associated with S as sulphides. The slag consisted of three different phases; namely the silicate phase (slag), metallic phase and the sulphide phases. The slag phases were mainly glass, silicate phases and metallic and sulphide phases. It was observed that the metallic and sulphide phases were dominant in the finer size fractions (-75 µm) whereas the sulphide phase was also present in the coarser size fractions (+300 µm). An important finding from the microscopy examination was that the sulphide phases were interstitial and could be liberated from the slag. This finding meant that liberation and subsequent concentration of the sulphide phases was feasible using conventional processing techniques.

6 October 2022 in Minerals
Verified
Journal Article
Open access
PDF file
Titus NghipulileTitus Nghipulile
Titus Nghipulile
TMThomas Ehongo Moongo
Thomas Ehongo Moongo
GDGodfrey Dzinomwa
Godfrey Dzinomwa
Sandile NkwanyanaSandile Nkwanyana
Sandile Nkwanyana
BMBenjamin Mapani
Benjamin Mapani
JKJaquiline Tatenda Kurasha
Jaquiline Tatenda Kurasha
The study evaluated the milling kinetics of three copper ores, from a multi-mineralised deposit, which were identified as sulphide 1 (with bornite as a dominant copper mineral), sulphide 2 (mainly composed of chalcopyrite) and oxide (with malachite as a dominant copper mineral) and related the breakage parameters to the mineral composition data. Five mono-size fractions between 1000 µm and 212 µm were dry milled for short grinding times in the laboratory ball mill in order to obtain data for predicting breakage rate parameters. The analytical and mineralogical characterisation of the ores were performed using X-ray fluorescence (XRF) analysis, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS) analysis, optical microscopy analysis and X-ray diffractometer (XRD). The mineralogy data showed that quartz was the abundant gangue mineral (average for each ore was above 60% (w/w)), followed by K-feldspar minerals (orthoclase and microcline) which constituted between 4% (w/w) and 6% (w/w) and the remainder are the minor calcite and dolomite minerals which are also in the host rock. The experimental milling kinetics parameters and mineralogical data were used to assess the robustness of the heterogeneous (two-component) and homogeneous (single-component) first-order rate breakage models. The mineral composition data were used for setting up the predictions of breakage parameters in the two-component and single-component first-order breakage models. The experimental data fitted better on the two-component breakage model than the single-component breakage model. These results highlighted the influence of two groups of minerals (generally classed as valuable and gangue minerals). The breakage data showed that the selection function for the hard component (the gangue minerals) has a dominant contribution to the overall selection function of the ores, with SiA correlating fairly well with experimental Si. The parameter a in the Austin empirical breakage model was relatively similar (approximately 1) for all three ores, which confirms similar milling conditions to which the ores were subjected to. The data suggests that there is a relationship between breakage parameter α (material-specific parameter) in the Austin empirical breakage model and brittleness index βi (calculated from the mineralogical composition of the gangue phase). No clear trends could be deduced from the cumulative breakage distributions of the three ores. This highlights the complexity of developing relationships between the mineralogical composition data and breakage distributions of the ores which are extracted from the same deposit and with comparable gangue composition.