Tommaso Pini

Dr. Tommaso Pini

Sapienza University, Rome, Lazio, Italy
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2017 in Engineering Fracture Mechanics
Verified
Journal Article
Open access
Tommaso PiniTommaso Pini
Tommaso Pini
FCF. Caimmi
F. Caimmi
BFBriatico-Vangosa Francesco
Briatico-Vangosa Francesco
RFR. Frassine
R. Frassine
MRM. Rink
M. Rink
The fracture behaviour of continuous unidirectional carbon fibre composite materials prepared adopting two, one plain and one rubber toughened, thermoplastic acrylic resins as matrices was investigated as a function of temperature and displacement rate. The contributions to fracture toughness of composites given by the matrix and the fibre related mechanisms was analysed by comparing results obtained at crack initiation and during crack propagation stages. It was verified that the transfer of matrix toughness into the composite is only partial when the matrix process zone size is comparable to the interlaminar matrix layer thickness. The effectiveness of fibre bridging mechanism was found to be related to the interfacial strength between the matrix and the fibre

14 June 2022 in Energy Technology
Verified
Journal Article
Open access
KTKevin M. Tenny
Kevin M. Tenny
KGKatharine V. Greco
Katharine V. Greco
MHMaxime van der Heijden
Maxime van der Heijden
Tommaso PiniTommaso Pini
Tommaso Pini
AMAdrian Mularczyk
Adrian Mularczyk
FBFikile Brushett
Fikile Brushett
Compressing porous carbon electrodes is a common approach to improve flow battery performance, but the resulting impact on electrode structure, fluid dynamics, and cell performance is not well understood. Herein, microtomographic imaging, load cell testing, and flow cell diagnostics are employed to characterize how compression‐induced changes impact pressure drop, polarization, and mass‐transfer scaling. Five different compressions are tested, spanning ranges typically used in literature, for AvCarb 1071 cloth (0%, 9%, 20%, 25%, 32%) and Freudenberg H23 paper (0%, 8%, 12%, 17%, 22%). It is found that the two electrode structures have distinct responses to compression, resulting in differing optimal conditions identified for each material; specifically, the Freudenberg H23 exhibits lower combined ohmic, charge‐transfer, and mass‐transport values at 8% compression, resulting in improved electrochemical performance across all compressive values, as compared to the optimal AvCarb 1071 compression (20%). Overall, Freudenberg H23 exhibits a greater sensitivity to compression with peak electrochemical activity correlating with increased permeability, whereas AvCarb 1071 is insensitive to compressive loads but produces lower electrochemical performance. Herein, the trade‐offs of mechanical robustness on fluid‐dynamic and electrochemical performance between the two electrodes are demonstrated by the aforementioned findings, suggesting each could be used for specific operating environments.

15 June 2017 in Polymer Engineering & Science
Verified
Journal Article
Closed access
PDF file
Tommaso PiniTommaso Pini
Tommaso Pini
BFBriatico-Vangosa Francesco
Briatico-Vangosa Francesco
RFRoberto Frassine
Roberto Frassine
MRMarta Rink
Marta Rink

1 November 2018 in Engineering Fracture Mechanics
Verified
Journal Article
Closed access
Tommaso PiniTommaso Pini
Tommaso Pini
BFBriatico-Vangosa Francesco
Briatico-Vangosa Francesco
RFR. Frassine
R. Frassine
MRM. Rink
M. Rink

29 December 2025 in Fibers
Verified
Journal Article
Open access
PDF file
Tommaso PiniTommaso Pini
Tommaso Pini
Gianluca CiarleglioGianluca Ciarleglio
Gianluca Ciarleglio
Elisa TotoElisa Toto
Elisa Toto
MariaGabriella SantonicolaMariaGabriella Santonicola
MariaGabriella Santonicola
Marco ValenteMarco Valente
Marco Valente
Electrospinning of poly(lactic acid) (PLA) commonly relies on toxic organic solvents, which limit its sustainability and biomedical applicability. In this work, a green electrospinning process was developed using dimethyl carbonate (DMC), a biodegradable and low-toxicity solvent, combined with acetone as a volatile co-solvent to promote efficient jet solidification. Three commercial PLA grades were evaluated for solubility and spinnability, and PLA 4043D was identified as the most suitable for DMC and acetone systems. The electrospinning parameters, including solvent ratio, flow rate, and applied voltage, were systematically optimized to achieve stable jet formation and uniform fiber morphology. Under optimized conditions, the process produced continuous, bead-free nanofibers with a mean diameter of ~1 µm and uniform nanoscale surface porosity resulting from differential solvent evaporation. The resulting fibers were characterized in terms of morphology, structure, thermal behavior, and mechanical performance, confirming increased amorphous content, high porosity (about 78%), and tensile strength of ~3 MPa for the selected electrospinning condition. This study demonstrates that DMC-based solvent systems enable a sustainable and potentially biocompatible route, considering the lower toxicity of the solvents employed, offering a green alternative to conventional toxic processes for the fabrication of medical scaffolds.

13 January 2025 in Fibers
Verified
Journal Article
Open access
PDF file
Tommaso PiniTommaso Pini
Tommaso Pini
Matteo SambucciMatteo Sambucci
Matteo Sambucci
Marco ValenteMarco Valente
Marco Valente
Global warming and climate change demand rapid and swift action in terms of reducing resource consumption, gas emissions, and waste generation. The textile industry is responsible for a large share of global pollution; therefore, to define a route to tackle part of the issue, a literature review on the current state of research in the field of recycling silk waste was conducted. The methods used to recover, process, and characterize silk waste fibers were summarized. The aim of this work was to investigate the possible applications of recycled silk waste in the field of composite materials for load bearing applications. In this sense, some prominent studies in the field of silk-based composites were reported, favoring thermoplastic materials for sustainability reasons. Studies on nonwoven silk waste fabrics were covered as well, finding an abundance of results but no applications as a reinforcement for composite materials. In a circular economy approach, we believe that the combination of nonwoven silk waste fabrics, thermoplastic polymers, and possibly hybridization with other fibers from sustainable sources could be beneficial and could lead to green and high-performance products. The aim of this work was to summarize the information available so far and help define a route in that direction.