Oleg Totosko

Dr. Oleg Totosko

computer-integrated technologies, Ternopil Ivan Puluj National Technical University, Ternopil, Ternopil’s’ka Oblast’, Ukraine
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 October 2022 in Challenges to national defence in contemporary geopolitical situation
Verified
Journal Article
Open access
PDF file
Oleg TotoskoOleg Totosko
Oleg Totosko
PSPetro Stukhlyak
Petro Stukhlyak
MMMytnyk Mykola
Mytnyk Mykola
NDNikolay Dolgov
Nikolay Dolgov
RZRoman Zolotiy
Roman Zolotiy
DSDanilo Stukhlyak
Danilo Stukhlyak
In this article, the influence of aggressive environments on a two-layer coating was investigated. Modern industry places high demands on quality control methods and coating properties during operation. It was established that the electrical resistance of epoxy composite samples depends significantly on the nature of the filler, the cohesive strength of the coatings, and the ambient temperature. We have determined the initial values of the volume resistance of epoxy composites and the temperature values when the samples lose their dielectric properties. The effectiveness of the use of electrospark water hammer treatment with the subsequent introduction of a bidisperse filler at optimal concentrations, which will increase the resist ance of protective coatings, is shown.

6 August 2023 in Mechanics of Advanced Materials and Structures
Verified
Journal Article
Closed access
NDNikolay Dolgov
Nikolay Dolgov
PSPetro Stukhlyak
Petro Stukhlyak
Oleg TotoskoOleg Totosko
Oleg Totosko
OMOlexandr Melnychenko
Olexandr Melnychenko
DSDanylo Stukhliak
Danylo Stukhliak
ICIhor Chykhira
Ihor Chykhira

1 January 2025 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
Oleg TotoskoOleg Totosko
Oleg Totosko
PSPetro Stukhliak
Petro Stukhliak
DSDanylo Stukhliak
Danylo Stukhliak
OYOleh YASNIY
Oleh YASNIY
The paper presents the results of studies of the physical and mechanical properties of materials: compressive failure stress, tensile failure stress, impact strength, and residual stresses in the material. To determine these parameters, we used modern methods of analyzing experimental studies, neural networks, to ensure a high measurement accuracy. Particular attention is paid to the research of the impact strength of residual stresses in the material, which allows for predicting the behavior of products in service. Impact toughness is one of the main indicators for evaluating materials that are operated under complex stress–strain conditions. It is proved that the values of both the compressive and tensile destructive stresses, impact strength, and residual stresses significantly affect the ability of the material to resist fracture under the action of both static and dynamic alternating loads. Critical values of residual stresses have been determined, the excess of which reduces the resistance of materials to fracture. The research has established the regularities of residual stresses and their magnitude in materials with different structural organizations. The research results are important from a scientific and technical point of view for the creation of new composite materials with high resistance to fracture, which will increase the operational reliability of the product as a whole.


1 August 2025 in Materials
Verified
Journal Article
Open access
PDF file
VKVolodymyr Korzhyk
Volodymyr Korzhyk
Volodymyr KopeiVolodymyr Kopei
Volodymyr Kopei
PSPetro Stukhlyak
Petro Stukhlyak
OBOlena Berdnikova
Olena Berdnikova
OKOlga Kushnarova
Olga Kushnarova
Liubomyr RopyakLiubomyr Ropyak
Liubomyr Ropyak
Difficult, extreme operating conditions of parabolic antennas under precipitation and sub-zero temperatures require the creation of effective heating systems. The purpose of the research is to develop a multilayer coating containing two metal-ceramic layers, epoxy composite layers, carbon fabric, and an outer layer of basalt fabric, which allows for effective heating of the antenna, and to study the properties of this coating. The multilayer coating was formed on an aluminum base that was subjected to abrasive jet processing. The first and second metal-ceramic layers, Al2O3 + 5% Al, which were applied by high-speed multi-chamber cumulative detonation spraying (CDS), respectively, provide maximum adhesion strength to the aluminum base and high adhesion strength to the third layer of the epoxy composite containing Al2O3. On this not-yet-polymerized layer of epoxy composite containing Al2O3, a layer of carbon fabric (impregnated with epoxy resin) was formed, which serves as a resistive heating element. On top of this carbon fabric, a layer of epoxy composite containing Cr2O3 and SiO2 was applied. Next, basalt fabric was applied to this still-not-yet-polymerized layer. Then, the resulting layered coating was compacted and dried. To study this multilayer coating, X-ray analysis, light and raster scanning microscopy, and transmission electron microscopy were used. The thickness of the coating layers and microhardness were measured on transverse microsections. The adhesion strength of the metal-ceramic coating layers to the aluminum base was determined by both bending testing and peeling using the adhesive method. It was established that CDS provides the formation of metal-ceramic layers with a maximum fraction of lamellae and a microhardness of 7900–10,520 MPa. In these metal-ceramic layers, a dispersed subgrain structure, a uniform distribution of nanoparticles, and a gradient-free level of dislocation density are observed. Such a structure prevents the formation of local concentrators of internal stresses, thereby increasing the level of dispersion and substructural strengthening of the metal-ceramic layers’ material. The formation of materials with a nanostructure increases their strength and crack resistance. The effectiveness of using aluminum, chromium, and silicon oxides as nanofillers in epoxy composite layers was demonstrated. The presence of structures near the surface of these nanofillers, which differ from the properties of the epoxy matrix in the coating, was established. Such zones, specifically the outer surface layers (OSL), significantly affect the properties of the epoxy composite. The results of industrial tests showed the high performance of the multilayer coating during antenna heating.

6 November 2025 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
PSPetro Stukhliak
Petro Stukhliak
Oleg TotoskoOleg Totosko
Oleg Totosko
OBOlena M. Berdnikova
Olena M. Berdnikova
DSDanylo Stukhliak
Danylo Stukhliak
In this work, it is proposed that the thermophysical properties of the composite material can be improved by modifying the binder with nanoscale additives. It is proved that the introduction of nanoparticles into oligomers at concentrations around 1% increases the thermal conductivity by 1.3–1.6 times. Macrosized particles were also used for comparison. It was found that this effect is achieved due to a decrease in thermal resistance at the interface in result of the formation of outer surface layers. Such modified binders are effective for creating various materials and coatings based on them with a wide range of characteristics.