This research aimed to produce gluten-free snacks on a pilot scale from quinoa flour. These snacks experienced an extrusion process, followed by baking. The effects of these technological processes on carbohydrate and protein digestibility, extractable phenolic compounds (EPP), hydrolyzable phenolic compounds (HPP), antioxidant capacity, and physical properties were evaluated in raw quinoa flour and extruded snacks. Extrusion increased digestible starch (RDS) from 7.33 g/100 g bs to 77.33 g /100 g bs. Resistant starch (RS) showed a variation of 2 g/100 g bs. It is noteworthy that protein digestibility increased up to 94.58 g/100 bs after extrusion and baking. These processes increased HPP content, while EPP and carotenoid content decreased. The samples showed significant differences (p < 0.05) in the antioxidant properties determined through the DPPH and ABTS methods. Values of 19.72 ± 0.81 µmol T/g were observed in snacks and 13.16 ± 0.2 µmol T/g in raw flour, but a reduction of up to 16.10 ± 0.68 µmol T/g was observed during baking. The baking process reduced the work of crispness (Wcr) from 0.79 to 0.23 N.mm, while the saturation (C*) was higher in baked ones, showing higher color intensity. The baking process did not influence the viscosity profile. The results in this study respond to the growing interest of the food industry to satisfy consumer demand for new, healthy, and expanded gluten-free snacks with bioactive compounds.

Protein functional properties are related to physical and chemical parameters that influence protein behavior in food systems during processing, storage and consumption. The structural and rheological properties of three quinoa hyperprotein flours (without defatting, WD, chemically defatted, CD, and mechanically defatted, MD) were evaluated. The values of the fluidity index (n) were significantly different (p < 0.05), which was associated with changes in protein or starch structures due to solvent treatments or heating of the flour during pressing. In addition, a strong dependence of the consistency index (k) on the shear rate was observed. For dispersions with a concentration of 12% (w/v), CD and WD had a significantly lower setback value than MD. The viscosity peak was affected by the presence of lipid molecules. Greater changes were evident in the β-sheet (1,610 and 1,625 cm⁻¹) and β-spin (1,685 and 1,695 cm⁻¹) structures. The changes identified in these structures were associated with the defatting treatment. Consequently, the intensity ratio 2,920/1,633 cm⁻¹ was more sensitive to changes in the fat content of the flours. It was shown that defatting conditions increase the protein adsorption kinetics and that the viscoelastic properties of the protein increase when the flour has a lower fat content. Hyperprotein quinoa flour could be used to improve the protein content of products such as snacks, pastas, ice cream, bakery products, meat extenders, among others, due to its foaming, gelling or emulsifying capacity. The objective of this work was to study the effect of two types of defatting of hyperprotein quinoa flour on its structural and rheological properties.

In recent years, great interest has been shown in pseudocereals for their high nutritional value. Wet milling has been used to obtain macromolecules such as proteins and starches. However, the co-products obtained from this food industry have been studied little. A factorial design Box-benhken was used to study the effect of surfactant concentration (SDS), sodium hydroxide (NaOH) concentration and maceration temperature on structural and colorimetric properties. Structural properties were evaluated by infrared spectroscopy (FTIR-ATR) and color changes by the CIElab tristimulus method (L^*, a^*, b^*). A decrease in temperature and NaOH causes a decrease in lightness (L^*), resulting in lower starch content and higher protein content in the co-product. This behavior was correlated with the infrared spectroscopy (FTIR-ATR) spectra. The spectra show a possible structural change in the amylose/amylopectin ratio of the starch granule at 1,012 cm⁻¹, 1,077 cm⁻¹, and 1,150 cm⁻¹ bands, which are associated with glycosidic bonds, these bonds were sensitive to NaOH concentration. While those bands assigned to Amide II (1,563 cm⁻¹) and Amide I (1,633 cm⁻¹), were sensitive to the effect of NaOH and maceration temperature, evidencing that protein content in the co-products is variable and depends significantly on the extraction conditions. The co-products obtained by wet milling could be used in the development of functional foods, such as bread, snacks, pasta and other products.