Vladimir Hristov

Prof. Dr. Vladimir Hristov

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 July 2025 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
GMGeorgi Mladenov
Georgi Mladenov
NKNikola Kuzmanov Kuzmanov
Nikola Kuzmanov Kuzmanov
Vladimir HristovVladimir Hristov
Vladimir Hristov
The present study focuses on the influence of brake fluid on the efficiency of a braking system. Consecutive tests were conducted on the brake discs of a laboratory vehicle heated to approximately 400 °C, and the temperature of the brake fluid was measured. The boiling points of the brake fluid in the brake system of the test vehicle were also measured and compared with other brake fluids of different brands but identical specifications. The brake fluids tested were both new brake fluids stored in an unopened state and brake fluids that had been opened for more than a year. This was intended to determine which of the elements has the most critical effect on the braking properties of the brake system.

1 January 2018 in Engineering Geology and Hydrogeology
Verified
Journal Article
Open access
TKTsvetan Kotsev
Tsvetan Kotsev
SKSava Kolev
Sava Kolev
Vladimir HristovVladimir Hristov
Vladimir Hristov
An attempt is made to model numerically the transport of dissolved substances caused by a difference in groundwater densities. It is supposed that initially at the surface of the aquifer a sector exists with high concentration of а pollutant (sulphates) while it is zero elsewhere in it. As a result, there is a higher water density near the surface. Due to this difference, a density driven flow arises and starts slow upwelling and downwelling movement of the water. The pollution located initially at the surface moves down and after a period of time reaches the bottom of the aquifer. Unsteady Darcy equation for creeping subsurface flow and mass transfer equation in a porous media were solved simultaneously in 2D area by the finite element method. The geometry of the area used in the calculations follows approximately the real contour of the aquifer. The aim of this study is to predict time needed for given amount of pollution coming from surface water into Quaternary aquifer to reach the lower Neogene aquifer. Plots representing the streamlines of the flow and concentration spreading for different times are shown.

25 July 2025 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
ASAnastasiya Slavova
Anastasiya Slavova
Vladimir HristovVladimir Hristov
Vladimir Hristov
One of the crucial tasks for autonomous robots is learning to safely navigate through obstacles in real-world environments. An intelligent robot must not only perform the assigned task but also adapt to changes in its environment as quickly as possible. In this work, we propose an improved version of the Deep Reinforcement Learning (DRL) Proximal Policy Optimization (PPO) algorithm by modifying a deep neural network of the Actor and Critic. Then we compare the results of our work by comparing them with those of classical PPO. Algorithm testing is conducted in a Flatland simulation environment, which allows for integration with the ROS2 operating environment.

1 January 2019 in Engineering Geology and Hydrogeology
Verified
Journal Article
Open access
MTMila Trayanova
Mila Trayanova
RARadostina Atanassova
Radostina Atanassova
Vladimir HristovVladimir Hristov
Vladimir Hristov
ABAleksey Dimitrov Benderev
Aleksey Dimitrov Benderev
The chemical composition of thermal waters has an important role in their use as a shallow geothemal source. One of the chemical components that may have a negative impact is iron. Its presence in the water can lead to both chemical and biocorrosion, as well as filling of the wells and facilities associated with the use of thermal waters. The aim of the study is to characterize the iron content and its present forms in thermal waters in Bulgaria. More than 250 samples of water sources revealing thermal waters are summarized and analyzed. In most cases iron concentrations are between 0.01 and 0.05 mg/l and in only 10% – it is above 0.1 mg/l. The forms of iron found in the water, the mineral phases, which can be formed, as well as their changes that occur with decreasing of temperature and increasing of the oxidation-reduction potential of the waters, are determined. It makes possible to predict the occurrence of undesirable processes (scaling and/or corrosion) for their exploitation after reaching the surface.

25 February 2026 in Energies
Verified
Journal Article
Open access
PDF file
Iliyan DamyanovIliyan Damyanov
Iliyan Damyanov
DSDurhan Saliev
Durhan Saliev
EDEvgeni Ts Dimitrov
Evgeni Ts Dimitrov
GMGeorgi Mladenov
Georgi Mladenov
MMMilena Georgieva Savova - Mratsenkova
Milena Georgieva Savova - Mratsenkova
DADimitar Asenov
Dimitar Asenov
This study presents a single-case multi-sensor experimental study of thermal loading and emission variation in a high-mileage gasoline engine operating at idle under deliberately impaired cooling until mechanical failure. A production vehicle equipped with a naturally aspirated gasoline engine with a displacement of 1600 cc was operated under relatively steady-state conditions at idle, while gaseous emissions (CO, CO2, HC, NOx, and O2), air–fuel ratio λ, particle number (PN), oil temperature, infrared thermal indicators, and acoustic performance variation were continuously monitored. The results are interpreted primarily in terms of their dependence on the engine oil temperature. They show that despite stable conditions of the air–fuel ratio and an almost constant amount of residual oxygen in the exhaust gases, progressive thermal loading leads to pronounced changes in the behavior of the emissions emitted by the engine during its operation. Hydrocarbon emissions show increased variability and escalation at elevated engine oil temperatures, while nitrogen oxides show a strong temperature-dependent increase, consistent with thermally driven formation mechanisms. The most significant response is observed in the particle number (PN) emissions, which go from low and stable levels to a rapid, multi-step increase in a narrow temperature range preceding mechanical failure. Under the tested cooling impairment scenario, emission behavior was dominated by cumulative thermal stress rather than mixture composition effects. In the investigated case, particle number emissions emerged as a sensitive indicator of system-level thermal instability. The findings provide experimentally documented insight into the system-level progression toward thermal runaway under impaired cooling conditions and its measurable impact on emission behavior in the tested engine.

23 May 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Iliyan DamyanovIliyan Damyanov
Iliyan Damyanov
DSDurhan Saliev
Durhan Saliev
Vladimir HristovVladimir Hristov
Vladimir Hristov
INIliyana Naydenova
Iliyana Naydenova
Tyre mass contributes to unsprung mass, rotating inertia, and broader vehicle-related characteristics, yet manufacturing mass variability among nominally identical passenger-car tyres remains comparatively insufficiently documented experimentally. This study investigates manufacturing mass variability in selected groups of new passenger-car tyres using a controlled repeatability-oriented weighing protocol. The primary dataset comprised 68 new passenger-car tyres grouped according to identical nominal specifications and available production characteristics, while six lightweight competition tyres were analysed separately as an auxiliary reference case. Each tyre was measured ten times with repositioning before every measurement under controlled indoor conditions. The observed repeatability remained within approximately 0.1–0.3 g, substantially below the between-tyre differences identified within several analysed groups. Descriptive statistical indicators, including mean mass, range, standard deviation, and coefficient of variation (CV), were used to evaluate within-group dispersion. The results confirmed experimentally detectable manufacturing mass variability among tyres with identical nominal specifications, including measurable differences between production batches of the same nominal tyre group. Among the analysed groups with sample size n ≥ 4, the lowest relative variability was observed for the Continental 275/35R21 tyres (CV = 0.05%), whereas the highest was identified for the summer Kleber 185/65R15 tyres (CV = 0.84%). The results demonstrate that tyre mass variability is experimentally detectable under controlled repeatable conditions and may represent a relevant engineering descriptor of manufacturing consistency.