When machining a small hole with high aspect ratio in EDM, it is hard for the flushing liquid entering the bottom gap and the debris could hardly be removed, which results in the accumulation of debris and affects the machining efficiency and machining accuracy. The assisted ultrasonic vibration can improve the removal of debris in the gap. Based on dynamics simulation software, Fluent, a three-dimensional (3D) model of debris movement in the gap flow field of EDM small hole machining assisted with side flushing and ultrasonic vibration is established in this paper. The laws of different amplitudes and frequencies and different aspect ratios on debris distribution and movement are quantitatively analyzed. The motion height of debris was observed under different conditions. The research results show that periodic ultrasonic vibration can promote the movement of debris, which is beneficial to the removal of debris in the machining gap. When compared to traditional small hole machining in EDM, the debris in the machining gap were greatly reduced, which ensures the stability of the machining process and improves the machining efficiency.
14 November 2019 in Advances in Materials Science and Engineering
Aiming at the problem of obvious tool length wear and side wear in the small hole processing of EDM, the nickel-coated composite electrode and diamond-nickel-coated composite electrode were prepared by chemical composite coating using brass, copper, molybdenum, and copper-tungsten alloy materials as the matrix material. Comparative experiments of EDM small hole machining using composite tools were carried out on die steel. The effects of nickel-coated composite electrode and diamond-nickel-coated composite electrode on tool length wear, tool side wear, and tool shape change were analyzed. The results show that the diamond-nickel-coated composite electrode can effectively reduce both the length wear and side wear of the electrodes.
28 June 2017 in Advances in Materials Science and Engineering
In electrical discharge machining (EDM) process, the debris removed from electrode material strongly affects the machining efficiency and accuracy, especially for the deep small hole machining process. In case of Ti alloy, the debris movement and removal process in gap flow between electrodes for small hole EDM process is studied in this paper. Based on the solid-liquid two-phase flow equation, the mathematical model on the gap flow field with flushing and self-adaptive disturbation is developed. In our 3D simulation process, the count of debris increases with number of EDM discharge cycles, and the disturbation generated by the movement of self-adaptive tool in the gap flow is considered. The methods of smoothing and remeshing are also applied in the modeling process to enable a movable tool. Under different depth, flushing velocity, and tool diameter, the distribution of velocity field, pressure field of gap flow, and debris movement are analyzed. The statistical study of debris distribution under different machining conditions is also carried out. Finally, a series of experiments are conducted on a self-made machine to verify the 3D simulation model. The experiment results show the burn mark at hole bottom and the tapered wall, which corresponds well with the simulating conclusion.
24 February 2019 in Advances in Materials Science and Engineering
With the development of (electrical discharge machining) EDM technology, composite tools with special features gradually replace the traditional single-material tools and have become widely used in specific processing conditions. In order to predict the wear of composite tool effectively, in this paper, a material removal model of single-pulse EDM with composite tools was established by using the finite element method. The surface temperature distribution of the composite tool was obtained by taking the copper-die steel tool as the analysis object. And the shape of discharge crater as well as the removal volume was obtained by the element birth and death method. The influences of discharge parameters and tool materials on the removal volume were analyzed respectively. The EDM experiments were carried out by using copper-die steel as the composite tool to verify the simulation results. It shows that the errors between actual machining results and the simulation results are less than 10%, which proves the accuracy of the simulation model.
1 January 2018 in Advances in Materials Science and Engineering
With the development of EDM technology, some multimaterial electrodes which have some special functions are regularly taking the place of traditional single material electrodes on some machining occasions and becoming widely used. In this paper, the influence of material on discharge breakdown in EDM with multimaterial electrodes is studied. A comparison model about material influence on discharge breakdown under both single discharge condition and continuous discharge condition is established, and the material property factors affecting the probability of discharge breakdown are also analyzed. Finally, a series of experiments are carried out to study the effects of different electrode materials on the discharge breakdown of EDM, a fitting formula of breakdown probability is presented, and the effectiveness of the comparison model is also verified by comparing with experimental results.
1 January 2019 in Engineering Applications of Computational Fluid Mechanics
Due to the complexity of electrical discharge machining (EDM), there is no perfect theory to explain the mechanisms of material erosion, ejection and solidification during the machining process. Therefore, this paper analyzed the micro-process of a single-pulse discharge during EDM and studied the thermal erosion, ejection and solidification processes of the electrode materials. A thermal-fluid simulation model that considered melting-solidification was established. A mathematical model of vapor flow considering the impact pressure was developed, and it was compiled and loaded as a material ejection force in simulations with a user defined function (UDF). The changes in the material ejection, crater formation and material solidification processes at different discharge times were studied. Finally, the simulation results were verified by single-pulse material discharge experiments, which provided a reference for additional understanding of the micro material discharge processes during EDM.