Fourier ptychography is a promising and flexible imaging technique that can achieve 2D quantitative reconstruction with higher resolution beyond the limitation of the system. Meanwhile, by using different imaging models, the same platform can be applied to achieve 3D refractive index reconstruction. To improve the illumination NA as much as possible while reducing the intensity attenuation problem caused by the LED board used in the traditional FP platform, we apply a hemispherical lighting structure and design a new LED arrangement according to 3D Fourier diffraction theory. Therefore, we could obtain the illumination of 0.98NA using 187 LEDs and achieve imaging half-pitch resolutions of ∼174 nm and ∼524 nm for the lateral and axial directions respectively, using a 40×/0.6NA objective lens. Furthermore, to reduce the number of captured images required and realize real-time data collection, we apply the multiplexed-coded illumination strategy and compare several coded patterns through simulation and experiment. Through comparison, we determined a radial-coded illumination pattern that could achieve more similar results as sequential scanning and increase the acquisition speed to above 1 Hz. Therefore, this paper provides the possibility of this technique in real-time 3D observation of in vitro live samples.
The inertial sensor is the key measurement payload of the technology verification satellite of China’s space gravitational wave detection mission-Taiji Project, which uses capacitive sensors to sense the acceleration disturbance of the test mass under the influence of non-conservative forces in the frequency range of 10 mHz~1 Hz. It is necessary to perform a ground performance evaluation and estimate the working state of the payload in orbit. However, due to the influence of the earth’s gravity and seismic noise, it is impossible to directly evaluate the resolution level of the non-sensitive axis when testing with high-voltage levitation, which leads to incomplete evaluation of the performance of the inertial sensor. In order to implement this part of the test, the sensitive structure is designed and a torsion pendulum facility for performance testing is developed. The experimental results show that the measurement resolution of the non-sensitive axis of the inertial sensor can reach 9.5 × 10−7 m/s2/Hz1/2 under the existing ground environmental conditions and is mainly influenced by the seismic noise during the system measurement. If the inertial sensor enters orbit, the measurement resolution can achieve 3.96 × 10−9 m/s2/Hz1/2, which meets the requirements of the technology verification satellite for a non-sensitive axis. This proposed system also provides a reasonable method for the comprehensive evaluation of inertial sensors in the future.
This study examines the measurement of film thickness, curvature, and defects on the surface or inside of an optical element using a highly accurate and efficient method. This is essential to ensure their quality and performance. Existing methods are unable to simultaneously extract the three types of information: thickness, curvature, and defects. Spectral-domain optical coherence tomography (SD-OCT), a non-invasive imaging technique with imaging depths down to the millimeter scale, provides the possibility of detecting the optical element components’ parameters. In this paper, we propose an error correction model for compensating delay differences in A-scan, field curvature, and aberration to improve the accuracy of system fitting measurements using SD-OCT. During data processing, we use the histogram-equalized gray stretching (IAH-GS) method to deal with strong reflections in the thin film layers inside the optics using individual A-scan averages. In addition, we propose a window threshold cutoff algorithm to accurately identify defects and boundaries in OCT images. Finally, the system is capable of rapidly detecting the thickness and curvature of film layers in optical elements with a maximum measurement depth of 4.508 mm, a diameter of 15 × 15 mm, a resolution of 5.69 microns, and a sampling rate of 70 kHz. Measurements were performed on different standard optical elements to verify the accuracy and reliability of the proposed method. To the best of our knowledge, this is the first time that thickness, curvature, and defects of an optical film have been measured simultaneously, with a thickness measurement accuracy of 1.924 µm, and with a difference between the calibrated and nominal curvature measurements consistently within 1%. We believe that this research will greatly advance the use of OCT technology in the testing of optical thin films, thereby improving productivity and product quality.
Precise measurement of high-steepness optical components is a critical challenge currently faced, which is being overcome through a groundbreaking high-steepness mirror sub-aperture stitching interferometric measurement method utilizing the instrument transfer function (ITF). A spherical step test plate was meticulously designed and manufactured based on ITF calibration principles. This essential tool enables the calibration of the ITF distribution at different spatial positions of the sub-aperture stitching instrument during the measurement of steep spherical mirrors. A comprehensive analysis then revealed a clear ITF distribution pattern, which made it possible to develop a data fusion algorithm model for the overlapping regions in the sub-aperture stitching process. In practical application, a highly successful stitching measurement was performed on a high-steepness spherical mirror with a diameter of 100 mm and a curvature radius of 103.314 mm. The experimental results demonstrate significant improvement in optical surface metrology. The full-aperture stitching achieved a peak-to-valley (PV) residual error of $0.073\lambda $ in the central region, with a root mean square (RMS) error of $0.002\lambda $ . Similarly, the edge region exhibited a PV error of $0.039\lambda $ and an RMS error of $0.002\lambda $ . These values represent a marked enhancement over conventional averaging-based fusion algorithms. These excellent results demonstrate the effectiveness of the method proposed in this study and provide a clear solution for high-precision measurement of steep optical components. This innovative method advances the field and sets a new benchmark for the precise measurement of optical component facets.
The micro capacitive sensing and electrostatic drive control system (front-end electronics, FEE) is the core component of inertial sensor in space gravitational wave detection. The FEE requires high-precision displacement detection, high-stability electrostatic drive, and stable system control to achieve an acceleration resolution of 10-15 m/s2/Hz1/2 in the low-frequency range of 0.1 mHzb–1 Hz. Based on the requirements of the future Chinese space gravitational wave detection task (Taiji Program), this paper conducted key technical research of the FEE using differential capacitance detections and electrostatic drives. The structure and working principle of the FEE were also introduced. The structural parameters of the entire system, working parameters, and electrostatic control system model were provided, and the performance of the PID controller was analyzed. Finally, using the torsion pendulum to overcome the influence of gravity on the earth, the FEE multi-degree of freedom control function was verified on the vibration isolation marble platform, the measurement range and power conversion coefficient were calibrated, and the noise level under current conditions was measured. Experimental results show that the FEE developed in this paper can achieve stable control in multiple degrees of freedom, the acceleration range is larger than 10-3 m/s2, the electric force conversion factor is 4.8×10-3 m/s2/V, and the measured acceleration resolution is 9.6×10-6 m/s2/Hz1/2. After optimizing the sensitive structure parameters, the acceleration resolution can be estimated at 3.3×10-15 m/s2/Hz1/2. These results satisfy the Taiji Program requirements. This paper provides a solid foundation for the future exploration of space gravitational waves in China and clears the optimization direction for the next step.
Free-space laser communication (FSLC) has attracted wide attention and developed rapidly due to its high bandwidth and strong capability to resist interception and interference. However, communication performance is severely affected by atmospheric turbulence. In this paper we consider the end face of the coupling fiber and adopted power-in-the-bucket (PIB) as the evaluation criterion instead of the traditionally used coupling efficiency. The relationship between FSLC performance (PIB) and adaptive optics parameters (corrected Zernike modes number) is derived for the first time. We simulated and conducted an 8.9 km horizontal FSLC experiment to analyze the effects of corrected modes on communication performance. The simulation and experiment results consistently show that, for turbulence of r0 = 7.51 cm, it is sufficient to correct the first 30 modes. The bit error rate (BER) and the PIB reached values of about 10−7 and 70%, respectively. For r0 = 4.43 cm correction of the first 22 modes, yielded BER and PIB values of around 10−5 and 55%, respectively. For r0 = 1.7 cm, no matter how many Zernike modes are corrected, the BER and PIB values are about 10−3 and 20% respectively. This experiment and its results provide an important reference for corrected modes on communication performance under different turbulence strengths.