Yeong Huei Lee

Dr. Yeong Huei Lee

Curtin University Malaysia

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
mugahed amranmugahed amran
mugahed amran
Roman FediukRoman Fediuk
Roman Fediuk
Nikolai Ivanovich VatinNikolai Ivanovich Vatin
Nikolai Ivanovich Vatin
YLYeong Huei Lee
Yeong Huei Lee
Murali GunasekaranMurali Gunasekaran
Murali Gunasekaran
HAHisham Alabduljabbar
Hisham Alabduljabbar
Foamed concrete (FC) is a high-quality building material with densities from 300 to 1850 kg/m3, which can have potential use in civil engineering, both as insulation from heat and sound, and for load-bearing structures. However, due to the nature of the cement material and its high porosity, FC is very weak in withstanding tensile loads; therefore, it often cracks in a plastic state, during shrinkage while drying, and also in a solid state. This paper is the first comprehensive review of the use of man-made and natural fibres to produce fibre-reinforced foamed concrete (FRFC). For this purpose, various foaming agents, fibres and other components that can serve as a basis for FRFC are reviewed and discussed in detail. Several factors have been found to affect the mechanical properties of FRFC, namely: fresh and hardened densities, particle size distribution, percentage of pozzolanic material used and volume of chemical foam agent. It was found that the rheological properties of the FRFC mix are influenced by the properties of both fibres and foam; therefore, it is necessary to apply an additional dosage of a foam agent to enhance the adhesion and cohesion between the foam agent and the cementitious filler in comparison with materials without fibres. Various types of fibres allow the reduction of by autogenous shrinkage a factor of 1.2–1.8 and drying shrinkage by a factor of 1.3–1.8. Incorporation of fibres leads to only a slight increase in the compressive strength of foamed concrete; however, it can significantly improve the flexural strength (up to 4 times), tensile strength (up to 3 times) and impact strength (up to 6 times). At the same time, the addition of fibres leads to practically no change in the heat and sound insulation characteristics of foamed concrete and this is basically depended on the type of fibres used such as Nylon and aramid fibres. Thus, FRFC having the presented set of properties has applications in various areas of construction, both in the construction of load-bearing and enclosing structures.

1 January 2017 in Environmental Engineering and Management Journal
Verified
Journal Article
Closed access
MPMohanadoss Ponraj
Mohanadoss Ponraj
YLYeong Huei Lee
Yeong Huei Lee
MDMohd Fadhil Md Din
Mohd Fadhil Md Din
ZNZainura Zainon Noor
Zainura Zainon Noor
KIKenzo Iwao
Kenzo Iwao
SCSHREESHIVADASAN CHELLIAPAN
SHREESHIVADASAN CHELLIAPAN

1 May 2017 in Energy and Buildings
Verified
Journal Article
Closed access
NANickholas Anting
Nickholas Anting
MDMohd. Fadhil Md. Din
Mohd. Fadhil Md. Din
KIKenzo Iwao
Kenzo Iwao
MPMohanadoss Ponraj
Mohanadoss Ponraj
KJKarlvin Jungan
Karlvin Jungan
ASAlvin John Lim Meng Siang
Alvin John Lim Meng Siang

1 April 2014 in Journal of Thermal Biology
Verified
Journal Article
Closed access
Mohd FadhilMohd Fadhil
Mohd Fadhil
YLYeong Huei Lee
Yeong Huei Lee
Ponraj MohanadossPonraj Mohanadoss
Ponraj Mohanadoss
DODilshan Remaz Ossen
Dilshan Remaz Ossen
KIKenzo Iwao
Kenzo Iwao
SCSHREESHIVADASAN CHELLIAPAN
SHREESHIVADASAN CHELLIAPAN

24 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
WCWei Quan Chin
Wei Quan Chin
YLYeong Huei Lee
Yeong Huei Lee
mugahed amranmugahed amran
mugahed amran
Roman FediukRoman Fediuk
Roman Fediuk
Nikolai Ivanovich VatinNikolai Ivanovich Vatin
Nikolai Ivanovich Vatin
YLYeong Huei Lee
Yeong Huei Lee
The fabrication of bricks commonly consumes relatively high natural resources. To reduce the carbon footprint in the brick production industry, repurposing industrial wastes in the making of sustainable bricks is a recent trend in research and application. Local wastes, such as oil palm shell (OPS), palm oil fuel ash (POFA), and quarry dust (QD), are massively produced annually in the palm oil-exporting countries. Moreover, QD from mining industries is hazardous to both water and air quality. For better waste management in marching towards sustainability, these wastes should be given their second life as construction materials. Therefore, this paper investigates the possibility of incorporating agro-industrial wastes into the brick mixture by examining their properties by means of several standardized tests. For the mix design, a 100% replacement of coarse aggregate with OPS, 20% replacement of cement with POFA, 20% cement weight of limestone as admixture, and 0 to 50% replacements of fine aggregate with QD are experimentally considered. The optimum mix of these wastes is preliminarily determined by focusing on high compressive strength as an indicator. Other examinations include splitting tensile, flexural strength, water absorption, and efflorescence tests. Although the agro-industrial waste cement brick is 18% lower in the strength to weight ratio compared to that of conventional, it is observed that it has better late strength development due to its POFA pozzolanic properties. Moreover, the proposed green cement brick is further checked for compliance with several standards for feasible use in the construction industry. Financially, the cost for the brick with the new mix design is almost equivalent to that of conventional. Hence, this green cement brick is reasonable to be employed in the construction industry to promote material sustainability for better waste management.

26 April 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
Yi Xuan TangYi Xuan Tang
Yi Xuan Tang
YLYeong Huei Lee
Yeong Huei Lee
mugahed amranmugahed amran
mugahed amran
Roman FediukRoman Fediuk
Roman Fediuk
Nikolai Ivanovich VatinNikolai Ivanovich Vatin
Nikolai Ivanovich Vatin
YLYeong Huei Lee
Yeong Huei Lee
The utilization of ordinary Portland cement (OPC) in conventional concretes is synonymous with high carbon emissions. To remedy this, an environmentally friendly concrete, alkaline-activated slag concrete (AASC), where OPC is completely replaced by ground granulated blast-furnace slag (GGBFS) industrial waste, is one of the currently pursued research interests. AASC is not commonly used in the construction industry due to limitations in experience and knowledge on the mix proportions and mechanical properties. To circumvent great labour in the experimental works toward the determination of the optimal properties, this study, therefore, presents the compressive strength prediction of AASC by employing the back-propagation artificial neural network (ANN) modelling technique. To construct this model, a sufficiently equipped experimental databank was built from the literature covering varied mix proportion effects on the compressive strength of AASC. For this, four model variants with different input parameter considerations were examined and the ideal ANN architecture for each model with the best input number–hidden layer neuron number–output number format was identified to improve its prediction accuracy. From such a setting, the most accurate prediction model with the highest determination coefficient, R2, of 0.9817 was determined, with an ANN architecture of 8-18-1 containing inputs such as GGBFS, a fine to total aggregate ratio, sodium silicate, sodium hydroxide, mixing water, silica modulus of activator, percentage of sodium oxide and water–binder ratio. The prediction accuracy of the optimal ANN model was then compared to existing ANN-based models, while the variable selection was compared to existing AASC models with other machine learning algorithms, due to limitations in the ANN-based model. To identify the parametric influence, the individual relative importance of each input variable was determined through a sensitivity analysis using the connection weight approach, whose results indicated that the silica modulus of the activator and sodium silicate greatly affected the AASC compressive strength. The proposed methodology demonstrates that the ANN-based model can predict the AASC compressive strength with a high accuracy and, consequently, aids in promoting the utilization of AASC in the construction industry as green concrete without performing destructive tests. This prediction model can also accelerate the use of AASC without using a cement binder in the concrete matrix, leading to produce a sustainable construction material.