This paper aims to improve car body stability performance by optimising locomotive parameters when coupler jack-knifing occurs during braking. In order to prevent car body instability behaviour caused by coupler jack-knifing, a multi-locomotive simulation model and a series of field braking tests are developed to analyse the influence of the secondary suspension and the secondary lateral stopper on the car body stability performance during braking. According to simulation and test results, increasing secondary lateral stiffness contributes to limit car body yaw angle during braking. However, it seriously affects the dynamic performance of the locomotive. For the secondary lateral stopper, its lateral stiffness and free clearance have a significant influence on improving the car body stability capacity, and have less effect on the dynamic performance of the locomotive. An optimised measure was proposed and adopted on the test locomotive. For the optimised locomotive, the lateral stiffness of secondary lateral stopper is increased to 7875 kN/m, while its free clearance is decreased to 10 mm. The optimised locomotive has excellent dynamic and safety performance. Comparing with the original locomotive, the maximum car body yaw angle and coupler rotation angle of the optimised locomotive were reduced by 59.25% and 53.19%, respectively, according to the practical application. The maximum derailment coefficient was 0.32, and the maximum wheelset lateral force was 39.5 kN. Hence, reasonable parameters of secondary lateral stopper can improve the car body stability capacity and the running safety of the heavy haul locomotive.
Turnouts are among the weakest links of railway lines, but the derailment risk of vehicles passing the through route of a turnout is seldom considered. The potential factors affecting derailment are screened according to field investigations of a train derailment case at the through route of a turnout. A detailed wagon-turnout interaction model considering the non-uniform cross-sections of turnout rails and the interaction between adjacent wagons is developed and validated. Through numerical simulation, the dynamic performance of an empty wagon passing the through route of turnout at a low speed is studied. When the wagon passes the turnout under the continuous lateral force condition, the wheels climb onto the rail head at the switch area in the facing direction, while the derailment occurs at the frog area in the trailing direction. Moreover, the possibility of derailment of the empty wagon increases with increasing coupler force and wheel-rail friction coefficient, and with decreasing speed. To improve the safety of empty wagons in the turnout area, rail lubrication should be implemented to reduce the wheel-rail friction coefficient, and large braking forces should be avoided. Furthermore, the wheel surface condition after re-profiling requires continuous attention.
The friction draft gear with hysteresis characteristics is one of the typical nonlinear elements in longitudinal train dynamics (LTD). Due to the nonlinear hysteresis of friction damping, the discontinuity between loading and unloading envelopes becomes a mathematical integration issue when adopting look-up table methods to establish draft gear models. It might cause integration divergence and wrong results if ignored. To solve this discontinuity, three different transitional strategies (velocity-dependent, intermediate slope, and smoothing approximation) are applied to building draft gear models, and the one-dimensional (1D) longitudinal train model adopting the ‘Zhai’ integration method is used. To ensure accurate results, the international benchmark cases of LTD are studied, and three draft gear models with different transitional strategies are compared in this paper. The results show that these three models can successfully work with ‘Zhai’ method in the LTD simulation to achieve the force agreement with benchmark cases. Compared to the other two models, the velocity-dependent model doesn’t exhibit good buffer deflection agreement and requires a smaller step size to achieve convergent results. Therefore, it is recommended that adopting the intermediate slope method or smoothing approximation approach avoids discontinuity problems of modelling draft gears in LTD.
The modelling of the wheel–rail contact is fundamental in the railway field since the contact forces directly affect vehicle dynamics, wear, safety and maintenance. In this context, the development of a realistic adhesion model able to describe degraded adhesion conditions is still an open problem because of the complex non-linear behaviour of the adhesion coefficient. To face this problem, in this work an innovative degraded adhesion model has been developed taking into account important phenomena like large sliding at the contact interface, the consequent energy dissipation and the adhesion recovery caused by the cleaning effect on the rail due to the friction forces. The new approach, based on FASTSIM algorithm and Polach theory, is numerically very efficient and has been specifically designed for multibody applications. The developed model has been validated through the comparison with experimental data related to suitable braking manoeuvres.