Muhammad Zia Ullah Khan

Mr. Muhammad Zia Ullah Khan

COMSATS University Islamabad, Sahiwal Campus
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 September 2020 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Muhammad Zia Ullah KhanMuhammad Zia Ullah Khan
Muhammad Zia Ullah Khan
EUEmad Uddin
Emad Uddin
BCBilal Akbar Chuddher
Bilal Akbar Chuddher
Naved AkramNaved Akram
Naved Akram
ANAli Ammar Naqvi
Ali Ammar Naqvi
Fausto Pedro García MárquezFausto Pedro García Márquez
Fausto Pedro García Márquez
A new micro heat exchanger was analyzed using numerical formulation of conjugate heat transfer for single-phase fluid flow across copper microchannels. The flow across bent channels harnesses asymmetric laminar flow and dean vortices phenomena for heat transfer enhancement. The single-channel analysis was performed to select the bent channel aspect ratio by varying width and height between 35–300 μm for Reynolds number and base temperature magnitude range of 100–1000 and 320–370 K, respectively. The bent channel results demonstrate dean vortices phenomenon at the bend for Reynolds number of 500 and above. Thermal performance factor analysis shows an increase of 18% in comparison to straight channels of 200 μm width and height. Alumina nanoparticles at 1% and 3% concentration enhance the Nusselt number by an average of 10.4% and 23.7%, respectively, whereas zirconia enhances Nusselt number by 16% and 33.9% for same concentrations. On the other hand, thermal performance factor analysis shows a significant increase in pressure drop at high Reynolds number with 3% particle concentration. Using zirconia for nanofluid, Nusselt number of the bent multi-channel model is improved by an average of 18% for a 3% particle concentration as compared to bent channel with deionized water.

1 December 2021 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
Muhammad Zia Ullah KhanMuhammad Zia Ullah Khan
Muhammad Zia Ullah Khan
MYM. Yamin Younis
M. Yamin Younis
Naved AkramNaved Akram
Naved Akram
BABilal Akbar
Bilal Akbar
URUmair Ahmed Rajput
Umair Ahmed Rajput
FZFahad Bin Zahid
Fahad Bin Zahid

1 December 2021 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
Muhammad Zia Ullah KhanMuhammad Zia Ullah Khan
Muhammad Zia Ullah Khan
BABilal Akbar
Bilal Akbar
RSRamisha Sajjad
Ramisha Sajjad
URUmair Ahmed Rajput
Umair Ahmed Rajput
SMSANAULLAH MASTOI
SANAULLAH MASTOI
Naved AkramNaved Akram
Naved Akram

17 November 2021 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
PDF file
GGGhulam Abbas Gohar
Ghulam Abbas Gohar
Muhammad Zia Ullah KhanMuhammad Zia Ullah Khan
Muhammad Zia Ullah Khan
Hassan RazaHassan Raza
Hassan Raza
AAArslan Ahmad
Arslan Ahmad
YRYasir Raza
Yasir Raza
MAMusa Arif
Musa Arif
The exhaust gases from an internal combustion (IC) engine carry away about 75% of the heat energy which means only 25% of heat energy is operated for power production. A recovery unit at the exhaust outlet port can ensure heat exchange between different temperature fluids through conjugate heat transfer phenomena. This study represents heat recovery from exhaust gases that are emitted from IC engines which can be utilized in various applications such as vapor absorption refrigeration systems. In the present work, a new type of perforated fin heat exchanger for waste heat recovery of exhaust gases is designed using SolidWorks, and the flow field design of the heat recovery system is optimized using ANSYS software. Various parameters (velocity, pressure, temperature, and heat conduction) of hot and cold fluid have been analyzed. Inlet velocity of cold fluids including refrigerant (LiBr solution), water, and graphene oxide (GO) nanofluid have been adopted at 0.03 m/s, 0.165 m/s, and 0.3 m/s, respectively. Inlet velocity of hot fluid is taken as 2 m/s, 4 m/s, and 6 m/s, respectively, to develop a test matrix. The results showed that maximum temperature reduction by the exhaust is achieved at 104.8°C using graphene oxide nanofluids with an inlet velocity of 0.3 m/s and exit velocity of 2 m/s in the heat recovery unit. Similarly, temperature reduction by exhaust gases is acquired at 102 °C using water and 96.34 °C by using a refrigerant (LiBr solution) with the same exit velocity (2m/s). Furthermore, maximum effectiveness of 0.489 is also obtained for GO nanofluid when compared with water and the refrigerant. On the other hand, the refrigerant has the maximum log mean temperature difference from all fluids with a value of 224.4 followed by water and GO.

17 August 2026 in Advanced Functional Materials
Verified
Journal Article
Open access
YZYiying Zou
Yiying Zou
MSMehmet Akif Sahin
Mehmet Akif Sahin
Muhammad Zia Ullah KhanMuhammad Zia Ullah Khan
Muhammad Zia Ullah Khan
MAMuhammad Usman Akhtar
Muhammad Usman Akhtar
DSDaniel Stoecklein
Daniel Stoecklein
GDGhulam Destgeer
Ghulam Destgeer
Continuous‐ and stop‐flow lithography are widely used to fabricate multi‐dimensional microstructures whose cross‐sectional morphology is dictated by the flow profile of multiple co‐flowing streams. Here, we introduce three‐dimensional hydrodynamic flow lithography (3D HFL), a platform for programmable generation of multi‐layered flow profiles and their conversion into solid anisotropic microparticles and fibers. By strategically combining variable inlet, intra‐channel pillar, and outlet configurations, we achieve precise and versatile sculpting of flow profiles under non‐inertial conditions, as validated by computational fluid dynamics simulations and experimental production of microparticles. The flow‐sculpting devices are fabricated using low‐cost 3D‐printed molds to cast PDMS channels with precisely aligned inlets and complex geometries that are difficult or impossible to achieve with conventional soft lithography. We demonstrate anisotropic multi‐material microparticles and fibers tailored for specific applications: amphiphilic particles for uniform microdroplet capture, biocompatible patterned hydrogels for controlled cell adhesion, and dual‐layer fibers for temperature sensing. To support this, we develope a rapid, predictive software tool for flow‐profile design and 3D particle engineering. Ultimately, 3D HFL integrates straightforward device fabrication, accessible computational design, and high‐throughput production into a scalable platform for creating microstructures with tailored geometries, compositions, and functionalities.

3 December 2023 in Energies
Verified
Journal Article
Open access
PDF file
ANAli Ammar Naqvi
Ali Ammar Naqvi
EUEmad Uddin
Emad Uddin
Muhammad Zia Ullah KhanMuhammad Zia Ullah Khan
Muhammad Zia Ullah Khan
Vortex generators and pin fins are conventionally used to deliver fluid mixing and improved convective heat transfer. The increased pressure loss following a fractional increase in heat transfer, as well as the complex manufacturing design, leave room for improvement. The present work proposes a novel diverging–converging base corrugation model coupled with vortex generation using simple geometrical modifications across rectangular microchannels to ensure a superior performance. The Nusselt number, friction factor, and flow phenomenon were numerically studied across a Reynolds number range of 50–1000. The optimum cross-section of the microchannel-generating vortices was determined after thorough study, and base corrugation was further added to improve heat transfer. For the vortex–corrugation modeling, the heat transfer enhancement was verified in two optimized cases: (1) curved corrugated model, (2) interacting corrugated model. In the first case, an optimized curve generating Dean vortices was coupled with base corrugation. An overall increase in the Nusselt number of up to 32.69% and the thermal performance of “1.285 TPF” were observed at a high Reynolds number. The interacting channels with connecting bridges of varying width were found to generate vortices in the counter-flow configuration. The thermal performance of “1.25 TPF” was almost identical to the curved corrugated model; however, a major decrease in pressure, with a loss of 26.88%, was observed for this configuration.