We report on a one-step writing process of a planar waveguide including a Bragg grating structure in bulk Polymethylmethacrylate (PMMA). A KrF excimer laser and a phase mask covered by an amplitude mask were used to locally increase the refractive index in PMMA and thereby generate simultaneously the planar waveguide and the Bragg grating. Our results show a reflected wavelength of the Bragg grating of about 1558.5 nm in accordance to the phase mask period. The reflectivity of the grating is about 80%. Initial characteristics of the Bragg grating structure towards humidity are investigated.
A polymer planar Bragg grating sensor is used for measuring both mechanical compressive and tensile strain. The planar waveguide with integrated Bragg grating is fabricated in bulk Polymethylmethacrylate in a single writing step using combined amplitude and phase mask technique. After butt coupling of a single-mode optical fiber the planar structure can be applied for measuring both mechanical tensile and compressive strain alongside the integrated waveguide without the need of further modifications. In this respect, we particularly report for the first time compressive strain measurements using a polymer Bragg grating. Furthermore, the sensitivity of the sensor against tensile and compressive strain, its reproducibility and hysteresis are investigated and discussed.
We demonstrate the application of polymer planar Bragg gratings for multi-axial strain sensing and particularly highlight simultaneous 2D strain measurement. A polymer planar Bragg grating (PPBG) fabricated with a single writing step in bulk polymethylmethacrylate is used for measuring both tensile and compressive strain at various angles. It is shown that the sensitivity of the PPBG strongly depends on the angle between the optical waveguide into which the grating is inscribed and the direction along which the mechanical load is applied. Additionally, a 2D PPBG fabricated by writing two Bragg gratings angularly displaced from each other into a single polymer platelet is bonded to a stainless steel plate. The two reflected wavelengths exhibit different sensitivities while tested toward tensile and compressive strain. These characteristics make 2D PPBG suitable for measuring multi-axial tensile and compressive strain.
We report an optical refractive index sensor system based on a planar Bragg grating which is functionalized by substituted γ-cyclodextrin to determine low concentrations of naphthalene in solvent vapor. The sensor system exhibits a quasi-instantaneous shift of the Bragg wavelength and is therefore capable for online detection. The overall shift of the Bragg wavelength reveals a linear relationship to the analyte concentration with a gradient of 12.5 ± 1.5 pm/ppm. Due to the spectral resolution and repeatability of the interrogation system, this corresponds to acquisition steps of 80 ppb. Taking into account the experimentally detected signal noise a minimum detection limit of 0.48 ± 0.05 ppm is deduced.
Embedded channel waveguide Bragg gratings are fabricated in the Ormocer® hybrid polymers OrmoComp®, OrmoCore, and OrmoClad by employing a single writing step technique based on phase mask technology and KrF excimer laser irradiation. All waveguide Bragg gratings exhibit well-defined reflection peaks within the telecom wavelengths range with peak heights of up to 35 dB and −3 dB-bandwidths of down to 95 pm. Furthermore, the dependency of the fabricated embedded channel waveguide Bragg gratings on changes of the temperature and relative humidity are investigated. Here, we found that the Bragg grating in OrmoComp® is significantly influenced by humidity variations, while the Bragg gratings in OrmoCore and OrmoClad exhibit linear and considerably high temperature sensitivities of up to −250 pm/ C and a linear dependency on the relative humidity in the range of −9 pm/%.
We report on the influence of the applied UV dosage on the fabrication of planar Bragg gratings in cyclo-olefin copolymers. Integrated waveguides with inscribed gratings are fabricated simultaneously using a single writing step technique and characterized by measuring the reflected and transmitted spectra. In addition, the effect of length and width of both waveguide and Bragg grating on the reflectivity and attenuation are studied using the cut-back method. The results show that in this material class, integrated waveguides with an attenuation as low as 1.2 dB/cm and Bragg gratings with a reflectivity of up to 99% can be realized. Most strikingly, we demonstrate that Bragg gratings with a length of only 2.1 mm still exhibit a distinct Bragg reflection facilitating miniaturized Bragg grating applications. Moreover, we demonstrate that the refractive index sensitivity of the planar Bragg gratings strongly depends on the UV dosage, in turn facilitating to tailor grating properties according device requirements in sensing applications.