Weigang Zhang

Prof. Dr. Weigang Zhang


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 November 2015 in Scientific Reports
Verified
Journal Article
Open access
PDF file
YTYuelong Tian
Yuelong Tian
MGMin Ge
Min Ge
WZWeigang Zhang
Weigang Zhang
XLXiaoxu Lv
Xiaoxu Lv
SYShouquan Yu
Shouquan Yu
Metallocene of zirconium were used as a catalyst for an insertion polymerization of 1-methylsilene directly into pre-ceramic precursor polyzirconocenecarbosilane (PZCS) during dechlorination of dichlorodimethylesilane by sodium, which exhibits high catalytic effectiveness with the maximum conversion ratio of polycarbosilane up to 91%. The average molecular weights of polymers synthesized are less than 1400, all with very narrow polymolecularities. The mechanism of catalytic polymerization was assumed to be similar to a coordination insertion polymerization of 1-olefins by metallocenes. The obtained PZCS show high ceramic yields with formation of composite ceramics of ZrC-SiC, which are novel polymeric precursors of ultra-high temperature ceramic (UHTC) fiber and composite.

4 November 2020 in Journal of the American Ceramic Society
Verified
Journal Article
Closed access
PDF file
HZHao Zhang
Hao Zhang
MGMin Ge
Min Ge
HZHuifeng Zhang
Huifeng Zhang
WKWeijia Kong
Weijia Kong
SYShouquan Yu
Shouquan Yu
WZWeigang Zhang
Weigang Zhang

11 April 2021 in Journal of Thermal Spray Technology
Verified
Journal Article
Closed access
PDF file
XSXiaoming Sun
Xiaoming Sun
ZLZhiang Liu
Zhiang Liu
LDLingzhong Du
Lingzhong Du
HLHao Lan
Hao Lan
HZHuifeng Zhang
Huifeng Zhang
WZWeigang Zhang
Weigang Zhang

9 February 2016 in RSC Advances
Verified
Journal Article
Closed access
PDF file
YTYuelong Tian
Yuelong Tian
WZWeigang Zhang
Weigang Zhang
MGMin Ge
Min Ge
SYShouquan Yu
Shouquan Yu
XLXiaoxu Lv
Xiaoxu Lv
TZTingting Zhang
Tingting Zhang
Competition between two different polymerization pathways to polymethylsilanes (PMS) and polycarbosilanes (PCS) was studied. This occurs in a Wurtz reduction-coupling reaction system during dechlorination of several dichloromethylsilanes via sodium in toluene. These two reactions do not carry on pari-passu, i.e., PMS is exclusively formed. However, PCS can be formed dominantly when some zirconocenes are introduced. This competition was introduced as a result of a tautomeric transformation from methylsilylene (MeRSi:) into 1-silene (CH2 SiRH). These are formed simultaneously as two intermediates but are influenced by the substitution of methyl, ethyl, phenyl or vinyl groups on silicon in the dichloromethylsilanes. Polymerization of methylsilylenes into PMS can be inhibited by deactivation of the sodium surface via chemical adsorption of zirconocene dichloride. Hence, the catalytic insertion polymerization of 1-silene intermediates into PCS occurs at the active sites of zirconocenes—this leads to the formation of PCS conversion ratios of 82% to 93% from dichloromethylsilanes with methyl, ethyl and phenyl as substituents. However, catalytic polymerization does not happen from dichloromethylvinylsilane. The mechanisms of insertion polymerization as well as the thermal dynamic barrier from polymethylvinylsilane (PMVS) to polyvinylcarbosilane (PVCS) are discussed in detail.

6 May 2020 in Materials
Verified
Journal Article
Open access
PDF file
MGMin Ge
Min Ge
LXLv Xiaoxu
Lv Xiaoxu
HZHao Zhang
Hao Zhang
SYShouquan Yu
Shouquan Yu
ZLZhenxi Lu
Zhenxi Lu
WZWeigang Zhang
Weigang Zhang
Continuous ceramic fiber comprising silicon carbide–zirconium carbide (SiC–ZrC) binary phases was obtained through melt spinning, electron-beam curing and pyrolysis of a pre-ceramic precursor of polyzirconocenecarbosilanes (PZCS). After pyrolysis and heat treatment, ZrC particles with mean diameters of 15–20 nm were formed and homogeneously dispersed in a matrix of fine crystalline β-SiC with an average grain size of 6–10 nm. Concentration of Zr in the fiber varies from 14.88% to 17.45% by mass. Fibers consisting of near-stoichiometric ZrC and SiC with little free carbon can be obtained through pyrolysis decarbonization of the as-cured fiber in hydrogen from room temperature to 1000 °C, and subsequently heat treatment in argon up to 1600 °C for 1 h. High-temperature treatment of these amorphous inorganic fibers leads to crystallization of the binary phases of β-SiC and ZrC. The removal of free carbon under hydrogen results in more rapid growth of β-SiC and ZrC crystals, in which obvious aggregation of the dispersed ZrC particles among the continuous β-SiC matrix can be ascribed to a fast migration of Zr cation.

27 March 2020 in Surface Engineering
Verified
Journal Article
Closed access
RLRuoyu Liu
Ruoyu Liu
HLHao Lan
Hao Lan
CHChuanbing Huang
Chuanbing Huang
LDLingzhong Du
Lingzhong Du
SFShige Fang
Shige Fang
WZWeigang Zhang
Weigang Zhang
Hexagonal boron nitride (h-BN) particles were added to a sliver metal matrix to improve the tribological properties of the prepared Ag–BN coatings, which were deposited via plasma spraying technique. The morphology, flowability and apparent density of Ag–BN composite powders were characterized, as well as the phase composition, microstructure and friction properties of Ag–BN coatings were systematically investigated. Results of XRD showed that Ag–BN coatings were successfully prepared, morphologies of SEM showed dense structures of Ag–BN coatings. The friction and wear behaviour of Ag–BN coatings was investigated from ambient temperature up to 800°C. The results showed that the coatings exhibited excellent tribological properties in this temperature range. The main wear mechanisms of Ag–BN coating were adhesive wear and ploughing. Layered h-BN reduced the friction coefficient and improved abradable property of Ag–BN coatings. Ag as the metal phase effectively protected the Si3N4 ball from wear.