Using an inverse analysis technique, the heat transfer coefficient on the die-workpiece contact surface of a hot stamping process was evaluated as a power law function of contact pressure. This evaluation was to determine whether the heat transfer coefficient on the contact surface could be used for finite element analysis of the entire hot stamping process. By comparing results of the finite element analysis and experimental measurements of the phase transformation, an evaluation was performed to determine whether the obtained heat transfer coefficient function could provide reasonable finite element prediction for workpiece properties affected by the hot stamping process.
1 May 2024 in Journal of Computational Design and Engineering
This paper introduces a sequential approximate optimization method that combines the finite element method (FEM), dynamic differential evolution (DDE), and artificial neural network (ANN) surrogate models. The developed method is applied to address two optimization problems. The first involves metamaterial design optimization for metal sheet architecture with binary design variables. The second pertains to optimizing process parameters in multi-stage metal forming, where the discrete nature arises owing to changing tool geometries across stages. This process is highly non-linear, accumulating contact, geometric, and material non-linear effects discretely through forming stages. The efficacy of the proposed optimization method, utilizing ANN surrogate models, is compared with traditionally used polynomial response surface (PRS) surrogate models, primarily based on low-order polynomials. Efficient learning of ANN surrogate models is facilitated through the FEM and Python integration framework. Initial data for surrogate model training are collected via Latin hypercube sampling and FEM simulations. DDE is employed for sequential approximate optimization, optimizing ANN or PRS surrogate models to determine optimal design variables. PRS surrogate models encounter challenges in dealing with non-linear changes in sequential approximate optimization concerning discrete characteristics such as binary design variables and discrete non-linear behavior found in multi-stage metal forming processes. Owing to the discrete nature, PRS surrogate models require more data and iterations for optimal design variables. In contrast, ANN surrogate models adeptly predict non-linear behavior through the activation function’s characteristics. In the optimization problem of metal sheet architecture for design Target C, the ANN surrogate model required an average of 4.6 times fewer iterations to satisfy stopping criteria compared with the PRS surrogate model. Furthermore, in the optimization of multi-stage deep drawing processes, the ANN surrogate model required an average of 6.1 times fewer iterations to satisfy stopping criteria compared with the PRS surrogate model. As a result, the sequential global optimization method utilizing ANN surrogate models achieves optimal design variables with fewer iterations than PRS surrogate models. Further confirmation of the method’s efficiency is provided by comparing Pearson correlation coefficients and locus plots.
Silicone resin has recently attracted great attention as a high-power Light Emitting Diode (LED) encapsulant material due to its good thermal stability and optical properties. In general, the abrupt curing reaction of the silicone resin for the LED encapsulant during the curing process induces reduction in the mechanical and optical properties of the LED product due to the generation of residual void and moisture, birefringence, and residual stress in the final formation. In order to prevent such an abrupt curing reaction, the reduction of residual void and birefringence of the silicone resin was observed through experimentation by introducing the multi-step cure processes, while the residual stress was calculated by conducting finite element analysis that coupled the heat of cure reaction and cure shrinkage. The results of experiment and analysis showed that it was during the three-step curing process that the residual void, birefringence, and residual stress reduced the most in similar tendency. Through such experimentation and finite element analysis, the study was able to confirm that the optimization of the LED encapsulant packaging process was possible.
Hot stamping is a method capable of manufacturing high-strength automotive body parts by inducing a martensitic phase transformation through forming and die quenching after heating a metal sheet into a high temperature austenite phase. However, it is not easy to solve various formability problems occurring in the hot stamping process due to the complexity of the process and material behavior during high temperature forming. In this study, fracture-related forming limits and martensite phase ratio were selected as criteria for evaluating hot stamping formability. First, a hot stamping test was performed on a T-type part that simplified the B-pillar, an automotive body part, and the fracture behavior according to the temperature and thickness of the sheet blank was investigated. Additionally, forming analysis was performed on the hot stamping process of mass-produced B-pillar parts by varying the temperature of the sheet blank, the thickness of the sheet blank, the die-blank friction coefficient, and the strain-rate sensitivity of material among various process and material variables. Based on the analysis results, the effect of each process and material variable on the hot stamping formability of B-pillar parts was quantitatively analyzed. By utilizing the results of this study, it will be possible to solve the formability problem that occurs in the mass-production hot stamping process for automotive body parts and improve the quality of parts in the future.