Gil Sang Yoon

Gil Sang Yoon


Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 August 2007 in Sensors
Verified
Journal Article
Open access
PDF file
WJWoo-Chul Jung
Woo-Chul Jung
YHYoungmoo Heo
Youngmoo Heo
GYGil Sang Yoon
Gil Sang Yoon
KSKwang-Ho Shin
Kwang-Ho Shin
SCSung-Ho Chang
Sung-Ho Chang
MCMyeong-Woo Cho
Myeong-Woo Cho
Recently, the polymeric micro-fluidic biochip, often called LOC (lab-on-a-chip), has been focused as a cheap, rapid and simplified method to replace the existing biochemical laboratory works. It becomes possible to form miniaturized lab functionalities on a chip with the development of MEMS technologies. The micro-fluidic chips contain many micro-channels for the flow of sample and reagents, mixing, and detection tasks. Typical substrate materials for the chip are glass and polymers. Typical techniques for micro-fluidic chip fabrication are utilizing various micro pattern forming methods, such as wet-etching, micro-contact printing, and hot-embossing, micro injection molding, LIGA, and micro powder blasting processes, etc. In this study, to establish the basis of the micro pattern fabrication and mass production of polymeric micro-fluidic chips using injection molding process, micro machining method was applied to form micro-channels on the LOC molds. In the research, a series of machining experiments using micro end-mills were performed to determine optimum machining conditions to improve surface roughness and shape accuracy of designed simplified micro-channels. Obtained conditions were used to machine required mold inserts for micro-channels using micro end-mills. Test injection processes using machined molds and COC polymer were performed, and then the results were investigated.

2 September 2020 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
KSKi Hyeok Song
Ki Hyeok Song
DLDong Wook Lim
Dong Wook Lim
JPJeong Yeon Park
Jeong Yeon Park
SHSeok Jae Ha
Seok Jae Ha
GYGil Sang Yoon
Gil Sang Yoon

27 May 2014 in Materials
Verified
Journal Article
Open access
PDF file
MSMin-Jae Song
Min-Jae Song
KKKwon-Hee Kim
Kwon-Hee Kim
GYGil Sang Yoon
Gil Sang Yoon
HPHyungpil Park
Hyungpil Park
HKHeung-Kyu Kim
Heung-Kyu Kim
Silicone resin has recently attracted great attention as a high-power Light Emitting Diode (LED) encapsulant material due to its good thermal stability and optical properties. In general, the abrupt curing reaction of the silicone resin for the LED encapsulant during the curing process induces reduction in the mechanical and optical properties of the LED product due to the generation of residual void and moisture, birefringence, and residual stress in the final formation. In order to prevent such an abrupt curing reaction, the reduction of residual void and birefringence of the silicone resin was observed through experimentation by introducing the multi-step cure processes, while the residual stress was calculated by conducting finite element analysis that coupled the heat of cure reaction and cure shrinkage. The results of experiment and analysis showed that it was during the three-step curing process that the residual void, birefringence, and residual stress reduced the most in similar tendency. Through such experimentation and finite element analysis, the study was able to confirm that the optimization of the LED encapsulant packaging process was possible.

31 October 2012 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
GKGun-Hee Kim
Gun-Hee Kim
GYGil Sang Yoon
Gil Sang Yoon
JLJeong-Won Lee
Jeong-Won Lee
HKHeung-Kyu Kim
Heung-Kyu Kim
MCMyeong-Woo Cho
Myeong-Woo Cho

4 May 2012 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
GKGun-Hee Kim
Gun-Hee Kim
GYGil Sang Yoon
Gil Sang Yoon
JSJong-In Son
Jong-In Son
MCMyeong-Woo Cho
Myeong-Woo Cho

31 January 2012 in Journal of Mechanical Engineering and Automation
Verified
Journal Article
Open access
PDF file
GKGun-Hee Kim
Gun-Hee Kim
JLJeong-Won Lee
Jeong-Won Lee
YHYoung-Moo Heo
Young-Moo Heo
GYGil Sang Yoon
Gil Sang Yoon
The polymeric biochip has been focused as a cheap, rapid and simplified method to replace the existing biochemical laboratory works. This biochip is formed miniaturized lab functionalities on a chip with the development of MEMS technology. This has many micro-fluidic channels for the flow of sample and reagents, mixing and detection task. Existing technologies for the biochip fabrication are utilizing various micro pattern forming methods, such as etching, LIGA, and micro-imprinting etc. In this study, an injection molding process with micro mold was applied to the mass production of polymeric biochip which contains micro-fluidic channel. Micro cutting process was applied to fabricate the core feature for molding micro-fluidic channel. Therefore, a series of micro cutting experiments using micro endmill were performed to determine optimum cutting conditions. Besides, the low temperature micro-cutting experiments using micro endmills were performed to improve the quality of micro mold core by reducing the burr and surface roughness. After the verification of low temperature micro-cutting process efficiency, this process was used to fabricate required mold core for micro feature. Finally, test injection molding process using manufactured micro mold and COC polymer were performed, and then the results were investigated.