Hyungpil Park

Dr. Hyungpil Park


Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 August 2015 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
HPHyungpil Park
Hyungpil Park
BCBaegsoon Cha
Baegsoon Cha
SCSeunghyun Cho
Seunghyun Cho
DKDonghan Kim
Donghan Kim
JCJae Huck Choi
Jae Huck Choi
BRByungohk Rhee
Byungohk Rhee

1 January 2014 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
HPHyungpil Park
Hyungpil Park
BCBaeg-Soon Cha
Baeg-Soon Cha
SPSoo-Bin Park
Soo-Bin Park
JCJae-Hyuk Choi
Jae-Hyuk Choi
DKDong-Han Kim
Dong-Han Kim
KLKye-Hwan Lee
Kye-Hwan Lee
In fluid-assisted injection molding, the distribution of the residual wall thickness on the inside and outside of the curved area is different, and void is formed due to the effect of the shrinkage on the outside where the residual wall thickness is thicker. The shrinkage that takes place in the residual wall is affected by the rheological changes in the polymer caused by temperature change and also by the thermal properties of the penetration fluid. In this study, the different effects on void formation in residual wall during fluid-assisted injection molding were analyzed, and water and silicone oil that had different thermal properties were used for the fluids. For this, heat transfer analysis and injection molding analysis were conducted. The void formation occurred due to the different temperature distribution and volumetric shrinkage in the direction of the residual wall in the curved area with a hollow section. It was also found that the void formation in the curved area decreased in the case of silicone oil compared to the case of water from simulation and experiments.

27 May 2014 in Materials
Verified
Journal Article
Open access
PDF file
MSMin-Jae Song
Min-Jae Song
KKKwon-Hee Kim
Kwon-Hee Kim
GYGil Sang Yoon
Gil Sang Yoon
HPHyungpil Park
Hyungpil Park
HKHeung-Kyu Kim
Heung-Kyu Kim
Silicone resin has recently attracted great attention as a high-power Light Emitting Diode (LED) encapsulant material due to its good thermal stability and optical properties. In general, the abrupt curing reaction of the silicone resin for the LED encapsulant during the curing process induces reduction in the mechanical and optical properties of the LED product due to the generation of residual void and moisture, birefringence, and residual stress in the final formation. In order to prevent such an abrupt curing reaction, the reduction of residual void and birefringence of the silicone resin was observed through experimentation by introducing the multi-step cure processes, while the residual stress was calculated by conducting finite element analysis that coupled the heat of cure reaction and cure shrinkage. The results of experiment and analysis showed that it was during the three-step curing process that the residual void, birefringence, and residual stress reduced the most in similar tendency. Through such experimentation and finite element analysis, the study was able to confirm that the optimization of the LED encapsulant packaging process was possible.

12 December 2013 in Materials
Verified
Journal Article
Open access
PDF file
KSKwangho Shin
Kwangho Shin
YHYoungmoo Heo
Youngmoo Heo
HPHyungpil Park
Hyungpil Park
SCSungho Chang
Sungho Chang
Byungohk RheeByungohk Rhee
Byungohk Rhee
In this study, we focus on making a double-sided metal plate with an internal structure, such as honeycomb. The stainless steel powder was used in the metal injection molding (MIM) process. The preliminary studies were carried out for the measurement of the viscosity of the stainless steel feedstock and for the prediction of the filling behavior through Computer Aided Engineering (CAE) simulation. PE (high density polyethylene (HDPE) and low density polyethylene (LDPE)) and polypropylene (PP) resins were used to make the sacrificed insert with a honeycomb structure using a plastic injection molding process. Additionally, these sacrificed insert parts were inserted in the metal injection mold, and the metal injection molding process was carried out to build a green part with rectangular shape. Subsequently, debinding and sintering processes were adopted to remove the sacrificed polymer insert. The insert had a suitable rigidity that was able to endure the filling pressure. The core shift analysis was conducted to predict the deformation of the insert part. The 17-4PH feedstock with a low melting temperature was applied. The glass transition temperature of the sacrificed polymer insert would be of a high grade, and this insert should be maintained during the MIM process. Through these processes, a square metal plate with a honeycomb structure was made.